Wilton 7020/7040 User Manual
7
Conductor Length
AWG (American Wire Gauge) Number
240 Volt Lines
240 Volt Lines
120 Volt Lines
0 - 50 Feet
No. 14
No. 14
50 - 100 Feet
No. 14
No. 12
Over 100 Feet
No. 12
No. 8
Safety Instructions on Sawing Systems
B
C
D
9. Always wear protective eye wear when operating,
servicing, or adjusting machinery. Eyewear shall
be impact resistant, protective safety glasses with
side shields complying with ANSI Z87.1 specifica-
tions. Use of eye wear which does not comply
with ANSI Z87.1 specifications could result in se-
vere injury from breakage of eye protection. See
Figure B.
be impact resistant, protective safety glasses with
side shields complying with ANSI Z87.1 specifica-
tions. Use of eye wear which does not comply
with ANSI Z87.1 specifications could result in se-
vere injury from breakage of eye protection. See
Figure B.
10. Nonslip footwear and safety shoes are recom-
mended. See Figure C.
11. Wear ear protectors (plugs or muffs) during e x -
tended periods of operation. See Figure D.
12. The workpiece, or part being sawed, must be
securely clamped before the saw blade enters
the workpiece.
the workpiece.
13. Remove cut off pieces carefully, keeping hands
away from saw blade.
14. Saw must be stopped and electrical supply dis-
connected before reaching into cutting area.
15. Avoid contact with coolant, especially guarding
your eyes.
A
General Electrical Cautions
This saw should be grounded in accordance with
the National Electrical Code and local codes and
ordinances. This work should be done by a qualified
electrician. The saw should be grounded to protect
the user from electrical shock.
ordinances. This work should be done by a qualified
electrician. The saw should be grounded to protect
the user from electrical shock.
1. Always wear leather gloves when handling saw
blade. The operator shall not wear gloves when
operating the machine.
operating the machine.
2. All doors shall be closed, all panels replaced, and
other safety guards in place prior to the machine
being started or operated.
being started or operated.
3. Be sure that the blade is not in contact with the
workpiece when the motor is started. The motor
shall be started and you should allow the saw to
come up to full speed before bringing the saw blade
into contact with the workpiece.
shall be started and you should allow the saw to
come up to full speed before bringing the saw blade
into contact with the workpiece.
4. Keep hands away from the blade area. See Fig-
ure A.
5. Remove any cut off piece carefully while keeping
your hands free of the blade area.
6. Saw must be stopped and electrical supply must
be cut off before any blade replacement or adjust-
ment of blade support mechanism is done, or be-
fore any attempt is made to change the drive belts
or before any periodic service or maintenance is
performed on the saw.
ment of blade support mechanism is done, or be-
fore any attempt is made to change the drive belts
or before any periodic service or maintenance is
performed on the saw.
7. Remove all loose items and unnecessary workpieces
from the area before starting machine.
8. Bring adjustable saw guides and guards as close
as possible to the workpiece.
19. Know the tool you are using — its application,
limitations, and potential hazards.
Wire Sizes
Caution: For circuits which are far away from the
Caution: For circuits which are far away from the
electrical service box, the wire size must be increased
in order to deliver ample voltage to the motor. To mini-
mize power losses and to prevent motor overheating
and burnout, the use of wire sizes for branch circuits
or electrical extension cords according to the following
table is recommended.
in order to deliver ample voltage to the motor. To mini-
mize power losses and to prevent motor overheating
and burnout, the use of wire sizes for branch circuits
or electrical extension cords according to the following
table is recommended.