White Rodgers 24A06G-1 User Manual

24A06G-1

DUAL LEVEL-TEMP

SILENT OPERATOR RELAY

(Normally Open Contacts)

PART NO. 37-4165C

Replaces 37-4165B

0504

INSTALLATION INSTRUCTIONS

Operator: Save these instructions for future use!

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL

INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL

INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL
INJURY AND/OR PROPERTY DAMAGE.

INJURY AND/OR PROPERTY DAMAGE.

PRECAUTIONS

To prevent electrical shock and/or equipment damage,

To prevent electrical shock and/or equipment damage,
disconnect electric power to system at main fuse or

disconnect electric power to system at main fuse or

disconnect electric power to system at main fuse or
circuit breaker box until installation is complete.

circuit breaker box until installation is complete.

CAUTION

WARNING

Do not use on circuits exceeding specified voltage.

Do not use on circuits exceeding specified voltage.
Higher voltage will damage control and could cause

Higher voltage will damage control and could cause

Higher voltage will damage control and could cause
shock or fire hazard.

shock or fire hazard.

This Dual Level-Temp Silent Operator Relay is designed for
controlling two separate loads with a single low voltage
thermostat. It is especially suitable for use with electric heating
equipment.

The Dual Level-Temp relay may be used to operate two
separate heating loads by means of a single low voltage
thermostat. It is equally well suited for use with a heating-
cooling thermostat to control heating and cooling loads alter-
nately as in motels, apartments, office buildings, etc.

This model Dual Level-Temp relay has a voltage input of 240
volts. Since this relay is equipped with a self-contained trans-
former, the supply voltage used must agree with the voltage
rating of the relay. This model has both an inductive and non-
inductive rating.

If in doubt about whether your wiring is millivolt, line, or low
voltage, have it inspected by a qualified heating and air
conditioning contractor, electrician, or someone familiar with
basic electricity and wiring.

Do not exceed the specification ratings.

All wiring must conform to local and national electrical codes
and ordinances.

This control is a precision instrument, and should be handled
carefully. Rough handling or distorting components could
cause the control to malfunction.

DESCRIPTION

SPECIFICATIONS

ELECTRICAL DATA

ELECTRICAL DATA
Switch Action:

Switch Action:

Switch Action: Two SPST switches, normally open
Thermal:

Thermal:

Thermal: Average time delay – 45 seconds
Ambient Temperature:

Ambient Temperature:

Ambient Temperature: -20° to 120°F (-24° to 49°C)
Mounting:

Mounting:

Mounting: 1/2" conduit hub or two key slot mounting holes

Thermostat Circuit Current:

Bimetal Heater #1 (Red & White Leads)

Bimetal Heater #1 (Red & White Leads) – 0.21 Amps
Bimetal Heater #2 (Red & Black with White Stripe

Bimetal Heater #2 (Red & Black with White Stripe

Bimetal Heater #2 (Red & Black with White Stripe
Leads)

Leads)

Leads) – 0.21 Amps

The Silent Operator relay has been carefully adjusted at the
factory, and no attempt should be made to adjust them in the
field.

TYPE

INPUT

NUMBER

VOLTAGE /FREQUENCY

ELECTRICAL RATING

FOR SWITCH #1

FOR SWITCH #2

(Red and Black Leads)

(Red Striped and Black Striped Leads)

NON-INDUCTIVE

INDUCTIVE*

NON-INDUCTIVE

INDUCTIVE*

24A06G-1

240VAC, 60 Hz

25A, 6000W

12 FLA (72 LRA)

25A, 6000W

12 FLA (72 LRA)

*FLA - Full Load Amps.; LRA - Locked Rotor Amps.

White-Rodgers is a division

of Emerson Electric Co.