White Rodgers 1F80-361 Installation Instruction

Page of 16
5
4)
4)
4)
4)
4) Select Energy Management Recovery OFF or ON
Select Energy Management Recovery OFF or ON
Select Energy Management Recovery OFF or ON
Select Energy Management Recovery OFF or ON
Select Energy Management Recovery OFF or ON -
Energy Management Recovery (EMR) causes the thermo-
stat to start heating or cooling early to make the building
temperature reach the program setpoint at the time you
specify. Heating will start 5 minutes early for every 1° of
temperature required to reach setpoint.
Example:
Example:
Example:
Example:
Example:  You select EMR and have your heating pro-
grammed to 65° at night and 70° at 7 AM. If the building
temperature is 65° the difference between 65° and 70° is
5°. Allowing 5 minutes per degree the thermostat setpoint
will change to 70° at 6:35 AM. Cooling allows more time per
degree because it takes longer to reach temperature.
5)
5)
5)
5)
5) Select filter replacement run time
Select filter replacement run time
Select filter replacement run time
Select filter replacement run time
Select filter replacement run time - The thermostat will
display  “FLTR” 
“FLTR” 
“FLTR” 
“FLTR” 
“FLTR”  after a set time of operation. This is a
reminder to change or clean your air filter. This time can be
set from 0 to 1950 hours in 50 hour increments. A selection
A selection
A selection
A selection
A selection
of 000 will cancel this feature.
of 000 will cancel this feature.
of 000 will cancel this feature.
of 000 will cancel this feature.
of 000 will cancel this feature. When “FLTR”
“FLTR”
“FLTR”
“FLTR”
“FLTR” is displayed,
you can clear it by pressing HOLD and RUN at the same
time. This resets the timer and starts counting the hours
until the next filter change. Changing the time in the menu
also resets the timer.
6)
6)
6)
6)
6) Select Compressor Lockout LOC OFF or ON
Select Compressor Lockout LOC OFF or ON
Select Compressor Lockout LOC OFF or ON
Select Compressor Lockout LOC OFF or ON
Select Compressor Lockout LOC OFF or ON - Selecting
LOC ON will cause the thermostat to wait 5 minutes before
turning on the compressor if the heating and cooling sys-
tem loses power. It will also wait 5 minutes minimum
between cooling cycles. This is intended to help protect the
compressor from short cycling. Some newer compressors
already have a time delay built in and do not require this
feature. Your compressor manufacturer can tell you if the
feature is already present in their system. When the com-
pressor time delay occurs it will flash the (snowflake icon)
for about five minutes then turn on the compressor.
7)
7)
7)
7)
7) Select Temperature Display Adjustment 4 LO to 4 HI
Select Temperature Display Adjustment 4 LO to 4 HI
Select Temperature Display Adjustment 4 LO to 4 HI
Select Temperature Display Adjustment 4 LO to 4 HI
Select Temperature Display Adjustment 4 LO to 4 HI -
Allows you to adjust the room temperature display 4° higher
or lower. Your thermostat was accurately calibrated at the
factory but you have the option to change the display
temperature to match your previous thermostat.
8)
8)
8)
8)
8) Select F° or C° Readout
Select F° or C° Readout
Select F° or C° Readout
Select F° or C° Readout
Select F° or C° Readout - Changes the display readout to
Centigrade or Fahrenheit as required.
OPERATING FEATURES
OPERATING FEATURES
OPERATING FEATURES
OPERATING FEATURES
OPERATING FEATURES
Now that you are familiar with the thermostat buttons and
display, read the following information to learn about the many
features of the thermostat.
• SIMULTANEOUS HEATING/COOLING PROGRAM
SIMULTANEOUS HEATING/COOLING PROGRAM
SIMULTANEOUS HEATING/COOLING PROGRAM
SIMULTANEOUS HEATING/COOLING PROGRAM
SIMULTANEOUS HEATING/COOLING PROGRAM
STORAGE 
STORAGE 
STORAGE 
STORAGE 
STORAGE — When programming, you can enter both
your heating and cooling programs at the same time. There
is no need to reprogram the thermostat at the beginning of
each season.
• TEMPERATURE OVERRIDE
TEMPERATURE OVERRIDE
TEMPERATURE OVERRIDE
TEMPERATURE OVERRIDE
TEMPERATURE OVERRIDE — Press 
 or 
 until the
display shows the temperature you want. The thermostat
will override current programming and keep the room
temperature at the selected temperature until the next
program period begins. Then the thermostat will automati-
cally revert to the program.
• HOLD TEMPERATURE
HOLD TEMPERATURE
HOLD TEMPERATURE
HOLD TEMPERATURE
HOLD TEMPERATURE — The thermostat can hold any
temperature within its range for an indefinite period without
reverting to the programmed temperature. Momentarily
press HOLD button. “HOLD”
“HOLD”
“HOLD”
“HOLD”
“HOLD” will be displayed. Then choose
the desired temperature by pressing 
 or 
. The
thermostat will hold the room temperature at the selected
setting until you press RUN button to start program opera-
tion again.
• CONFIGURATION MENU
CONFIGURATION MENU
CONFIGURATION MENU
CONFIGURATION MENU
CONFIGURATION MENU — Allows you to customize
certain thermostat options.
PROGRAMMING YOUR THERMOSTAT
PROGRAMMING YOUR THERMOSTAT
PROGRAMMING YOUR THERMOSTAT
PROGRAMMING YOUR THERMOSTAT
PROGRAMMING YOUR THERMOSTAT
This section will help you plan your thermostat’s program to
meet your needs. For maximum comfort and efficiency, keep
the following guidelines in mind when planning your program.
• When heating (cooling) your building, program the
temperatures to be cooler (warmer) when the building is
vacant or during periods of low activity.
• During early morning hours, the need for cooling is
usually minimal.
1
  Step 
Press Button(s) 
Displayed (Factory Default)    Press          or          to select:            
COMMENTS
HOLD
(0:00)
0 to 8 hrs (in 
15 minute increments)
2
(FA)
SL
Select temporary Hold time
4
5
E
(ON)
OFF
6
7
 LOC
(OFF)
ON
0 HI
(0)
4 LO to
4 HI
(F)
C
Returns to normal operation
8
9
Select Energy Management Recovery OFF or ON
Select compressor lockout OFF or ON
Select temperature display adjustment higher or lower
Select temperature display to  F or  C
RUN
PRGM
and RUN
HOLD*
HOLD*
3
d-L
(ON)
OFF
Select display backlight OFF or ON
HOLD*
HOLD*
Filter
(000)
0 to 1950 hours
(in 50 hour increments)
Select filter replacement run time
HOLD*
HOLD*
HOLD*
Select FA or SL (Fast or Slow) heating cycle rate
Configuration Menu
* Press 
HOLD to advance to next item or TIME to move backwards to previous item