Alpine CDA-9887R User Manual
16
-EN
01GB05CDA-9887R.fm
ALPINE CDA-9887R 68-08564Z21-A (EN)
Adjusting Bass/Treble/Balance (Between
Left and Right)/Auto Volume/Fader
(Between Front and Rear)/Defeat
Left and Right)/Auto Volume/Fader
(Between Front and Rear)/Defeat
1
Press AUDIO/RTN repeatedly to choose the desired
mode.
mode.
Each press changes the mode as follows:
SUBWOOFER
*
1
BASS
*
2
TREBLE
*
2
BALANCE
FADER
*
3
AUTO VOLUME
*
4
DEFEAT
VOLUME
SUBWOOFER
*
1
Subwoofer: 0 ~ +15
Bass level:
Bass level:
–
7 ~ +7
Treble level:
–
7 ~ +7
Balance: L15 ~ R15
Fader: R15 ~ F15
Auto Volume: OFF/LOW/MIDDLE/HIGH
Defeat: ON/OFF
Volume: 0 ~ 35
Fader: R15 ~ F15
Auto Volume: OFF/LOW/MIDDLE/HIGH
Defeat: ON/OFF
Volume: 0 ~ 35
• If no operation is performed for 5 seconds after selecting the
SUBWOOFER, BASS, TREBLE, BALANCE, FADER, AUTO
VOLUME or DEFEAT mode, the unit automatically returns to
normal mode.
VOLUME or DEFEAT mode, the unit automatically returns to
normal mode.
*
1
When the subwoofer mode is set to OFF, its level cannot be adjusted.
*
2
When the MultEQ (page 16) is set to OFF, its level cannot be
adjusted.
adjusted.
*
3
If you set the 4.2ch/2.2ch switch (pages 40 to 42) to 2.2ch, you
cannot adjust this mode.
cannot adjust this mode.
*
4
By setting AUTO VOLUME, the unit can automatically adjust
volume to a proper level according to engine/road noise, etc. There
are three volume correction degrees: LOW, MIDDLE and HIGH.
volume to a proper level according to engine/road noise, etc. There
are three volume correction degrees: LOW, MIDDLE and HIGH.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of BASS,
TREBLE and EQ will return to the factory defaults, and MX
(page 22) is turned off.
TREBLE and EQ will return to the factory defaults, and MX
(page 22) is turned off.
• Depending on the connected devices, some functions and display
indications do not work.
Turning MultEQ on/off
MultEQ, developed by Audyssey Labs, automatically corrects the audio
for the listening environment. The system is optimized for selected
positions in the vehicle. To accomplish this, MultEQ must take
measurements of the vehicles response characteristics. For details on the
set up procedure, consult your authorized Alpine dealer.
for the listening environment. The system is optimized for selected
positions in the vehicle. To accomplish this, MultEQ must take
measurements of the vehicles response characteristics. For details on the
set up procedure, consult your authorized Alpine dealer.
Press MultEQ to select ON/OFF mode.
• If MultEQ is turned on and its button pressed and held for at least 2
seconds, the Curve mode is switched (only when curve1 and curve2 are
stored).
stored).
• When using MultEQ, MX, X-OVER, T.Correction, User’s EQ,
Parametric EQ and Graphic EQ are set automatically. They are no
longer user adjustable.
longer user adjustable.
• When an external audio processor is connected, the MultEQ function
cannot be used.
Equalizer Presets
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
musical source material.
1
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
seconds to setup the Selection mode.
2
Turn the Rotary encoder to select AUDIO mode,
and then press
and then press
/
/ENT.
Bluetooth
GENERAL
AUDIO
DISPLAY
TUNER
Bluetooth
3
Turn the Rotary encoder to select Factory’s EQ
mode, and then press
mode, and then press
/
/ENT.
4
Turn the Rotary encoder to select the desired
equalizer characteristic, and then press
equalizer characteristic, and then press
/
/ENT.
Flat
Pops
Rock
News
Jazz&Blues
Electrical Dance
Hip Hop&Rap
Easy Listening
Country
Classical
User1
User2
User3
User4
User5
User6
• By selecting User’s 1 to 6, you can recall the stored preset number in
“Adjusting and Storing the Graphic Equalizer Curve” (page 17) or
“Adjusting and Storing the Parametric Equalizer Curve” (page 17) .
“Adjusting and Storing the Parametric Equalizer Curve” (page 17) .
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
seconds to return to normal mode.
• Pressing AUDIO/RTN during the procedure will return to the
previous mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
• This function is inoperable when DEFEAT is set to ON (page 16).
• Press and hold
• Press and hold
/ESC for at least 2 seconds, the setting mode is
cancelled.
Setting EQ mode
This setting gives you a choice of 5-band parametric, or 7-band
graphic equalizer.
graphic equalizer.
1
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
seconds to setup the Selection mode.
2
Turn the Rotary encoder to select AUDIO mode,
and then press
and then press
/
/ENT.
Bluetooth
GENERAL
AUDIO
DISPLAY
TUNER
Bluetooth
3
Turn the Rotary encoder to select EQ Mode, and
then press
then press
/
/ENT.
Sound Setting
BAND/TA
Rotary encoder
AUDIO/RTN
/
ESC
A.SEL
SOURCE
/
FUNC./SETUP
MultEQ
/ /
ENT
Preset buttons
(1 through 6)
01GB00CDA-9887R.book Page 16 Thursday, March 15, 2007 3:55 PM