Sharp SD-HX600 User Manual
E-16
SD_HX600_SEC_SECL_E1.fm
04/3/15
ENGLISH
TINSKA016AWZZ
F
S
V
I
N
P
E
E
SD-HX600
Pr
epara
tion f
o
r Us
e
- S
p
e
a
k
e
r c
onne
c
ti
o
n
/ Ante
nna
c
o
nne
c
tion
-
!
Connecting speaker wires
Make sure to leave the AC power cord disconnected when connecting the
speakers.
Connect the speaker wires to the speakers first, then to the unit.
speakers.
Connect the speaker wires to the speakers first, then to the unit.
When using a speaker wire:
Caution:
"
Use a speaker system which has 100 W or more rated power input and 4 - 8
ohm impedance.
ohm impedance.
"
If the volume is turned up too high with the speakers of less than 4 ohm imped-
ance connected, the protection circuit of the amplifier is activated. No sound is
produced temporarily.
ance connected, the protection circuit of the amplifier is activated. No sound is
produced temporarily.
"
Do not mistake the and , and right and left terminals of the speaker wires. (The
right speaker is placed on the right when you face the unit.)
right speaker is placed on the right when you face the unit.)
"
When the center and surround speakers and subwoofer are not connected, set the
speaker size to "C-NO", "S-NO" and "SW-NO". Otherwise, the protection circuit
may be activated and the power is turned off.
speaker size to "C-NO", "S-NO" and "SW-NO". Otherwise, the protection circuit
may be activated and the power is turned off.
Antenna connection
Note:
Placing the antenna on the unit or near the AC power cord may cause noise pickup.
Place the antenna away from the unit for better reception.
Place the antenna away from the unit for better reception.
Installing the AM loop antenna:
Outdoor FM or AM antenna:
Use an outdoor FM or AM antenna if you require better reception. Consult your
dealer.
When using an outdoor AM antenna, be sure to keep the wire of the AM loop antenna
connected.
dealer.
When using an outdoor AM antenna, be sure to keep the wire of the AM loop antenna
connected.
1
Strip the speaker wire about 5/8" (15
mm) and twist the conductors.
mm) and twist the conductors.
2
Loosen the speaker terminal.
3
Insert the speaker wire and tighten the
thumbscrew.
thumbscrew.
"
Do not short-circuit the speaker wire. If it happens with the
power on, the protection circuit is activated and the unit is
set to the power stand-by mode. In this case, check that the
speaker wire is connected correctly before turning on the
power again.
power on, the protection circuit is activated and the unit is
set to the power stand-by mode. In this case, check that the
speaker wire is connected correctly before turning on the
power again.
Incorrect
Approx. 5/8" (15 mm)
Supplied FM antenna:
Connect the FM antenna wire to the FM 75
OHMS jack and position the FM antenna wire in
the direction where the strongest signal can be
received.
OHMS jack and position the FM antenna wire in
the direction where the strongest signal can be
received.
Supplied AM loop antenna:
Connect the AM loop antenna wire to the AM
and GND terminals. Position the AM loop anten-
na for optimum reception. Place the AM loop an-
tenna on a shelf, etc., or attach it to a stand or a
wall with screws (not supplied).
and GND terminals. Position the AM loop anten-
na for optimum reception. Place the AM loop an-
tenna on a shelf, etc., or attach it to a stand or a
wall with screws (not supplied).
< Assembling >
< Attaching to the wall >
Wall
Screws
(not
supplied)
White
Black
FM antenna
AM loop
antenna
Outdoor FM antenna
Outdoor AM antenna
49 feet (15 m)
49 feet (15 m)
25 feet (7.5 m )
AM loop
antenna
antenna
Ground wire
Ground rod