Panasonic Attune II Installation Guide

10



p Before using an unformatted SDHC or SD card, format it 

first using the Center Module. When a card is formatted, 
whatever has been recorded on it will be erased. If an 
unformatted SDHC or SD card or an SDHC or SD card 
formatted on a unit other than the Center Module is 
used, it may not work properly or its performance may be 
compromised.



p When some SDHC or SD cards are used in this unit, 

they may not work properly or their performance may be 
compromised. Use of the recommended SDHC and SD 
cards is recommended. 
Recommended SDHC and SD cards 
Manufactured by Panasonic Corporation (sold separately) 
SDHC cards: 4 GB, 8 GB, 16 GB, 32 GB 
SD cards: 2 GB 
(Excluding miniSD cards and microSD cards)



p In many cases when SD cards are formatted or their data 

is erased or deleted using the functions of the Center 
Module or a personal computer, the data on the cards 
may not be erased completely. Before handling a card 
over to another party, it is recommended that you use 
a commercially available PC software application for 
erasing data to erase the data on the card completely.



p When SD cards are to be disposed of, either break them 

physically or erase the data on them completely, separate 
them in the garbage and dispose of them following the 
regulations that are enforced in the locality concerned.



p It is recommended that the touch panel be cleaned at 

regular intervals.



p If there is any noticeable dirt, dust, oil, grease, etc. on the 

touch panel, clean it immediately.



p Wipe off the dirt or dust gently using a soft dry cloth.



p You may damage the LCD display if you wipe or press the 

touch panel too forcefully or subject the display to impact 
or heavy loads.



p Do not use liquid or spray cleaners. The touch panel 

functions may be impaired as a result.



p Do not allow products made of rubber or PVC to remain 

in contact with the touch panel for prolonged periods of 
time. Doing so may cause discoloration or deterioration.



p Do not use benzene, paint thinners, adhesives, alkali- or 

alcohol-based cleaning agents, glass cleaners, waxes, 
abrasive cleansers, powdered cleaners, insecticides, etc. 
Doing so may cause colors and texture to be degraded. 
(When using a chemical cloth for cleaning, read the 
caution provided with the chemical cloth product.)



wInstallation precautions

In order to safeguard against injury, this 

device must be mounted on a wall, following the steps in 
the Operating Instructions.



p Locations exposed to direct sunlight



p Locations subject to having strong vibration or impact



p Locations which are not level



p Locations under the air conditioner



p Locations near the fryer



p Locations near the grill



p Locations where a chemical agent is used such as a 

swimming pool



p Locations near magnetic field sources such as a 

television or speakers



p Locations where condensation forms easily, where 

temperature changes greatly, humid places



p Locations subject to dust



p Locations subject to water splash or spray



p Locations where radiation or x-ray emissions are produced

The accessory power cord is to be used only with this unit.
Do not use it for any other devices. Similarly, do not use the 
power cords of other devices with this unit.

Grounding
Confirm that the wire is connected from the SIGNAL GND 
terminal to earth ground. A grounding connection must be 
made before connecting the power plug or this product to 
the main power supply. When disconnecting the grounding 
wire, make sure that the power plug of this product is 
disconnected from the main power supply.

Power supply used
The supply voltage of this unit is AC 100 V to 120 V 
(50 Hz/60 Hz). Connect this unit to a power supply with a 
sufficiently high capacity.

To cut the power supply
This product has no power switch. To cut the power supply,
unplug the power plug of the product from the AC outlet. If 
it is hard to unplug the power cord due to the installation 
conditions, connect the power cord of the product to the AC 
outlet via the circuit breaker of a distribution board or to the 
AC inlet socket of a power supply control unit.
Be sure to connect the power cord via any of the following 
breaking devices:



p Connect the power cord via a power supply control unit.



p Install the product near a power outlet, and connect the 

power cord via the power plug.



p Connect the power cord to the breaker with contact gap 

of 3.0 mm or more of a distribution board. The breaker 
shall be able to shut down all the poles of the main power 
supply except the ground protective conductor.

Setting the time
Before operating this unit, you must set the time. For how 
to set the time, refer to the Operating Instructions <Setup 
Instructions>.