Korg Bicycle PS60 User Manual
98
026: Tube Pre (Tube PreAmp
Modeling)
Modeling)
This effect simulates a two‐stage vacuum tube preamp. You
can make individual settings for two vacuum tubes
connected in series. This lets you create the warm sound
typical of vacuum tubes.
can make individual settings for two vacuum tubes
connected in series. This lets you create the warm sound
typical of vacuum tubes.
Saturation [%]
With higher settings of this value, the waveform will change
at high gain levels, tending to cause distortion. Lower
settings of this value will produce linear response.
at high gain levels, tending to cause distortion. Lower
settings of this value will produce linear response.
Tube1 Bias
This expresses the effect that changes in vacuum tube bias
have on the distortion of the waveform. Higher settings of
have on the distortion of the waveform. Higher settings of
this value will produce distortion even at low gain levels.
Since this will also change the overtone structure, you can
use it to control the tonal character.
Since this will also change the overtone structure, you can
use it to control the tonal character.
Tube1 Phase
With the Wet Invert setting, the phase of the signal will be
inverted between stage 1 and stage 2. Since “Bias” is applied
to the inverted signal in stage 2, this will change the tonal
character.
inverted between stage 1 and stage 2. Since “Bias” is applied
to the inverted signal in stage 2, this will change the tonal
character.
027: St.TubPre (Stereo Tube PreAmp
Modeling)
Modeling)
This is a stereo vacuum tube preamp simulator (See “026:
Tube Pre (Tube PreAmp Modeling)” on page 98.).
Tube Pre (Tube PreAmp Modeling)” on page 98.).
028: Mic Model (Mic Modeling +
PreAmp)
PreAmp)
This effect simulates a mic and vacuum tube preamp. You
can choose from various types of mic and positions to create
differing sonic characters.
can choose from various types of mic and positions to create
differing sonic characters.
Full
parameter
parameter
Quick
parameter
parameter
Value
Explanation
Tube1
Low Cut [Hz]
Low Cut [Hz]
T1 L[Hz]
Thru,
21...8.00k
21...8.00k
Sets the cutoff
frequency for the low
cut filter of stage 1
frequency for the low
cut filter of stage 1
Tube1
High Cut
[Hz]
High Cut
[Hz]
T1 H[Hz]
53...20.00k,
Thru
Thru
Sets the cutoff
frequency for the high
cut filter of stage 1
frequency for the high
cut filter of stage 1
Tube1
Gain [dB]
Gain [dB]
T1 G[Hz]
–24.0...+24.0
Sets the input gain for
stage 1
stage 1
Tube1
Saturation
[%]
Saturation
[%]
T1 Saturat
0...100
Sets the input/output
response for stage 1
response for stage 1
Tube1 Bias
T1 Bias
0...100
Sets the bias voltage
for stage 1
for stage 1
Tube1 Phase T1 Phase
Normal,
Wet Invert
Wet Invert
Turns phase reversal
on/off
on/off
Tube2
Low Cut [Hz]
Low Cut [Hz]
T2 L[Hz]
Thru,
21...8.00k
21...8.00k
Sets the cutoff
frequency for the low
cut filter of stage 2
frequency for the low
cut filter of stage 2
Tube2
High Cut
[Hz]
High Cut
[Hz]
T2 H[Hz]
53...20.00k,
Thru
Thru
Sets the cutoff
frequency for the high
cut filter of stage 2
frequency for the high
cut filter of stage 2
Tube2
Gain [dB]
Gain [dB]
T2 G[Hz]
–24.0...+24.0
Sets the input gain for
stage 2
stage 2
Tube2
Saturation
[%]
Saturation
[%]
T2 Saturat
0...100
Sets the input/output
response for stage 2
response for stage 2
Tube2 Bias
T2 Bias
0...100
Sets the bias voltage
for stage 2
for stage 2
Tube2
Output Level
[dB]
Output Level
[dB]
Lvl [dB]
–48.0...+0.0
Sets the output level
Wet/Dry
←
Dry, 1 : 99...
99 : 1, Wet
99 : 1, Wet
Source
Off...Tempo
Amount
–100...+100
+
Tube Pre Amp1
Tube Pre Amp2
Left
Right
Wet / Dry
Output Level
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Invert
-
Mic/Pre Amp - Saturation
In
Out
Saturation = 0
Saturation = 50
Saturation = 100
Bias = 0
Full
parameter
parameter
Quick
parameter
parameter
Value
Explanation
Mic Type
Mic
Vintage
Dynamic,
Multi
Condenser,
Percussion
Condenser,
Drums Dynamic,
Vocal Dynamic,
Multi Dynamic,
Vocal
Condenser,
Vocal Tube,
Kick Dynamic
Dynamic,
Multi
Condenser,
Percussion
Condenser,
Drums Dynamic,
Vocal Dynamic,
Multi Dynamic,
Vocal
Condenser,
Vocal Tube,
Kick Dynamic
Selects the type of
mic
mic
Mic Position
Mic Posit
Close, On,
Off, Far
Off, Far
Tube
Low Cut [Hz]
Low Cut [Hz]
T L[Hz]
Thru,
21...8.00k
21...8.00k
Sets the frequency of
the low cut filter
the low cut filter
In
Out
Satulation = 50
Bias = 0
Bias = 50
Bias = 100
Mic/Pre Amp - Bias
Left
Right
Wet / Dry
Output Level
Wet / Dry
Stereo In - Stereo Out
Tube Pre Amp1
Tube Pre Amp2
Tube Pre Amp1
Tube Pre Amp2
Left
Right
Wet / Dry
Wet / Dry
–
+
–
+
Invert
+
Tube Pre Amp
Mic Simulation
Left
Right
Wet / Dry
Output Level
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out