Memorex Camcorder MCC221 User Manual
22
EN
23
EN
Section 8
Specifications and System Requirements
Specification
Image sensor
VGA CMOS sensor
Operation modes
Video record, Photo capture
Lens
f=3.89mm; F2.4
Focus range
Full Range
Zoom
1X~2X (2X Digital)
Shutter
Electronic
LCD monitor
2.0”LCD (Measured diagonally)
Storage media
Built-in 2GB memory (200MB of memory is used for system software)
Record up to 2 hours of video or capture up to 20,000 photos.
Image resolution
640 x 480 (VGA)
Video resolution
VGA 640X480(30fps)
Power Source
USB Power
Battery Recording Time
5 hours
Exposure
+1EV~ -1EV
File format
Picture: JPG (Baseline)
Video: MOV
Image play
Single Image
Speaker
1 x 8 ohm
PC interface
USB 2.0 Port
TV out
NTSC/PAL Selectable
Battery
Lithium-ion Rechargeable Battery (NP-60, 3.7V 1050mAh)
Dimension
4.19(H) x 2.36(W) x 0.71(D) inches
Weight
0.16 lb (without battery)
Minimum System Requirement
Windows:
Microsoft Windows XP/Vista
•
Pentium IV 3.0 GHz or equivalent AMD Athlon
•
Intel ® Core™ 2 Duo CPU E6300 processor
•
(or higher recommended), AMD Athlon 64 X2
3800+ or higher for HD Video
512 MB RAM (1GB recommended)
3800+ or higher for HD Video
512 MB RAM (1GB recommended)
•
300 MB available hard disk space
•
NVIDIA FX5200 or ATI 9200 (or higher)
•
1024 x 768 pixels, 32-bit color monitor
•
Macintosh:
Mac OS 10.3, 10.4, 10.5
•
PowerPC G4 800 MHz processor or Intel
•
processor
512 MB RAM
512 MB RAM
•
150 MB available hard disk space
•
800 × 600 pixels, 16-bit color monitor
•
Note
The LCD screen is manufactured using extremely high-precision technology so over 99.99% of
the pixels are operational for effective use. However, some tiny black and/or bright dots (white,
red, blue or green) may appear on the LCD screen. These dots are a normal result of the
manufaturing process, and do not affect the recording quality.
Reset the Camcorder
If the camcorder acts erratically, reset it by removing the battery. Then reload the battery and turn on
the camcorder again.
the camcorder again.
Formatting the Camcorder
WARNING!
The contained video/photo editing software may lost by formatting the camcorder.
Do not format this camcorder unless it stops working and you are instructed to do so by
technical support personnel.
To format the camcorder:
Press the USB latch down and the USB arm pops out automatically.
1.
Connect the camcorder to the computer.
2.
Double click on [My Computer], then right click [Memorex] and left click on [Format].
3.
At the “Format” window, click [OK] to confirm and the camcorder will start to format (see figure
4.
below). When finished, click [OK] to close the Format window.
Format window for
“Memorex”
“Memorex”
Note
Make sure you have selected "FAT 32" at the file system pull-down menu; otherwise, after
formatting, the camera will not work properly. Then, click [OK] to confirm and the camcorder
will start to format. When finished, click [Close] to close the Format window.
formatting, the camera will not work properly. Then, click [OK] to confirm and the camcorder
will start to format. When finished, click [Close] to close the Format window.
For Firmware Upgrade
Please visit our Web site at www.memorex.com to check if there is new firmware available.
IMPORTANT NOTE: Before upgrading the firmware, please back-up all of your media files on your
computer. After upgrading, format the unit to complete the upgrade procedure.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE AT:
WWW.MEMOREX.COM
FOR CONSUMER REPLACEABLE PART(S), SEE PART NUMBER(S) ON PAGE 4, AND THEN
CONTACT OUR PARTS FULFILMENT CENTER, FOX INTERNATIONAL AT: 1-800-321-6993.