Elk Products Cross Platform Control elk-m1 User Manual

M1 Installation and Programming Manual

Page 25

12345678901234567890123456789012123

001 09:=No

Duress

12345678901234567890123456789012123

001: Sel

Prg

User 1

12345678901234567890123456789012123

001 01:12345678

Code used inArea

12345678901234567890123456789012123

001 02:=Yes

Arm with Code

12345678901234567890123456789012123

001 03:=Yes

Disarm with Code

12345678901234567890123456789012123

001 04:=Yes

Bypass with Code

12345678901234567890123456789012123

001 05:=No

Access with Code

Menu 02 - User Code Options

There are 99 potential User codes. User 1 (001) is the first to display. Press the right
arrow key to program, or press the up or down arrow keys to select another user. Enter
three digits to jump to a specific user. The user name is displayed along the bottom.

This option assigns the areas(s) in which this code may be used. For example: if the
numbers 1,2, & 4 are displayed, the code may be used in those areas. To assign or
remove an area press the numbers keys 1 thru 8. Each press toggles the number on/off.

Selects Arm privileges. If Yes, this code can Arm it’s assigned area(s) (see option 01
above) from a keypad that is also assigned to the desired area. If No, this code cannot be
used to Arm.

Selects Disarm privileges. If Yes, this user code can Disarm it’s assigned area(s) (see
option 01 above) from a keypad that is also assigned to the desired area. If No, this code
cannot be used to Disarm.

A Yes allows this code to Bypass zones whenever Menu 04-Keypad Definitions, Option
09, “Byp Key Req PIN” is set to Yes. Code and Keypad must be in the same area.
Default value for both these options is No (code not required for bypass).

A Yes allows this code to activate the Access Keypad Events 1313-1328 for the keypad
where code is entered. Use the Whenever/And/Then Rules from Elk-RP to assign an
output to this event for tripping a door strike or lock. Note: If this code is enabled for
arming, it will be necessary to press the Exit or Stay key to arm after the code.

If Yes, this code can only disarm if the control was armed by it or another temporary code.
In other words: A temporary code cannot disarm the control if a regular code was used to
arm. A temporary code might be used for cleaning, repair personnel, etc.

A Master Code can be used to review, change, or delete other users, and to modify
selected system options. Only one Master code is needed per system. For security
purposed, multiple Master codes are not recommended.

When Menu 07 - Global System Definitions, Option 41, “Require Code User Menu 1-5” is
set to a Yes, this option is then used to set which codes are allowed to access Menus 1 -
5. NOTE: Menus 6, 7, and 8 are only available to a Master or Installer code.

If Yes, this code will cause a silent Duress or “holdup” alarm to activate when the code is
used to arm or disarm the system. CAUTION: The communicator report code MUST
also be programmed! This feature is dangerous and should be used with caution.

To edit the User (Name) text press the left arrow key. Enter text using the number keys.
I.E. For a “K” press the 5 key twice. To move the cursor, press the RIGHT or LEFT arrow
keys. The Chime key inserts a space, the Bypass key erases 1 digit. The up/down keys
to toggle between upper and lower case. Press the ELK key when complete.

12345678901234567890123456789012123

001 06:=No

Temporary Code

12345678901234567890123456789012123

001 07:=Yes

Master Code

12345678901234567890123456789012123

001 08:=No

Menu 1-5 Allowed

12345678901234567890123456789012123

02-UserCode Optn
Code used to:

User Code Options

Description of Option

12345678901234567890123456789012123

001 10:Usr Name

User1

Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.

Default Code for User Code 1 is: 3 4 5 6 Note: If six digit code option is enabled, the
default will be 1 2 3 4 5 6. See Menu 07 - Global System Definitions, Option G11