Fluke Portable Multimedia Player 8842a User Manual
8842A
Instruction Manual
3-32
Table 3-3. Immediate-Mode Commands for Various Controllers
FUNTION
PERFORMED
FLUKE-BASIC on
1720A or 1722A
HP-HPL on
HP9825
Calculator
HP-BASIC on
HP9816-PC and HP-
85 Calculator
TEK-BASIC on
4051 Graphics
System
INITIALIZE Port
INIT PORT 0
cli 7
CLEAR 7
INIT
CLEAR Instrument
CLEAR @4
cir 704
CLEAR 704
PRINT @4: “*”
REMOTE Commands
REMOTE @4
rem 704
REMOTE 704
WBYTE @36, 17:
LOCAL Control
LOCAL @4
Icl 704
LOCAL 704
WBYTE @36, 1:
EXTERNAL TRIGGER
PRINT @4,”T1”
wrt 704,”T1”
OUTPUT 704;”T1”
PRINT @4:”T1”
TRIGGER Instrument
TRIG @4
trg 704
TRIGGER 704
PRINT @4:”?”
GET Output Data
INPUT @4,A
red 704, A
ENTER 704;A (Note 2)
INPUT @4:A
PRINT Data to Screen
PRINT A
prt A
PRINT A (Note 2)
PRINT A
CONFIGURE for VAC
PRINT @4,”F2”
wrt 704,”F2”
OUTPUT 704;”F2”
PRINT @4:”F2”
CONFIGURE for
200Vac
200Vac
PRINT @4,”R4”
wrt 704;”R4”
OUTPUT 704;”R4”
PRINT @4:”R4”
TRIGGER Continuously
PRINT @4,”TO”
wrt 704,”TO”
OUTPUT 704; “TO”
PRINT @4:”TO”
SUFFIXES Enable
PRINT @4,”Y1”
wrt 704,”Y1”
OUTPUT 704;”Y1”
PRINT @4:”Y1”
GET Data & Suffix
INPUT @4, A,A$
Red 704,A,A$
(Note 1)
(Note 1)
ENTER 704;A,A$ (Note
2)
2)
INPUT %4:A,A$
PRINT Data & Suffix
PRINT A,A$
Prt A$,A
PRINT A,A$ (Note 2)
PRINT A,A$
Notes:
1.
Before using A$ on the 9825 is necessary to enter ”dimA$[6]” to allocate a string variable. This statement allows
six characters.
six characters.
2.
In the HP9816 system, variables cannot be created from the keyboard; they must be created by running a
program. (See error 910 for that system.) To get around this, type in a very short program as follows:
program. (See error 910 for that system.) To get around this, type in a very short program as follows:
SCRATCH (Hit “EXEC” key)
10 A = 0 (Hit “ENTER” key)
20 A$ = ‘’’’ (Hit “ENTER” key)
30 END (Hit “ENTER” key)
(Hit “RUN” Key)
10 A = 0 (Hit “ENTER” key)
20 A$ = ‘’’’ (Hit “ENTER” key)
30 END (Hit “ENTER” key)
(Hit “RUN” Key)
This program creates the variables ‘A’ and ‘A$’ so that they may be accessed in immediate mode and changed at
will. This program is not necessary for the HP-85 Calculator.
will. This program is not necessary for the HP-85 Calculator.
3-60. EXAMPLE PROGRAMS
Several example programs for the 8842A using various controllers are presented in the
remaining figures in this section. In all of these examples, the 8842A is set to IEEE-488
address 4 (rear panel switch setting 000100). Of course, any other address (00 to 30)
could be substituted.
remaining figures in this section. In all of these examples, the 8842A is set to IEEE-488
address 4 (rear panel switch setting 000100). Of course, any other address (00 to 30)
could be substituted.
In each of these examples, the instrument is cleared prior to configuration set-ups. This
ensures that the 8842A configuration has been completely defined.
ensures that the 8842A configuration has been completely defined.
To run these programs, it is not necessary to type in all the comments (which appear to
the right of the exclamation marks). Also, spaces are placed between commands for ease
of reading; they are not required.
the right of the exclamation marks). Also, spaces are placed between commands for ease
of reading; they are not required.