Streamlight StreamLight Car Stereo System DEH-P3000IB User Manual

INST

ALLA

TION MANUAL

MANUEL D’INST

ALLA

TION

DEH-P3000IB

Printed in China

Imprimé en Chine

<CRD4246-A/S> UC

Installation

English

Installation

English

Connecting the unit

English

Note

• Check all connections and systems before final in-

stallation.

• Do not use unauthorized parts. The use of unau-

thorized parts may cause malfunctions.

• Consult with your dealer if installation requires drill-

ing of holes or other modifications of the vehicle.

• Do not install this unit where:

— it may interfere with operation of the vehicle.

— it may cause injury to a passenger as a result

of a sudden stop.

• The semiconductor laser will be damaged if it over-

heats. Install this unit away from hot places such as

near the heater outlet.

• Optimum performance is obtained when the unit is

installed at an angle of less than 60°.

DIN Front/Rear-mount

This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.

DIN Front-mount

Installation with the rubber bush

1. Insert the mounting sleeve into the

dashboard.

• When installing in a shallow space, use a

supplied mounting sleeve. If there is enough

space behind the unit, use factory supplied

mounting sleeve.

2. Secure the mounting sleeve by

using a screwdriver to bend the
metal tabs (90°) into place.

3. Install the unit as illustrated.

182

Removing the Unit

1. Extend top and bottom of the trim

ring outwards to remove the trim
ring. When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)

• It becomes easy to remove the trim ring if the

front panel is released.

2. Insert the supplied extraction keys

into both sides of the unit until they
click into place.

3. Pull the unit out of the dashboard.

DIN Rear-mount

1. Extend top and bottom of the trim

• It becomes easy to remove the trim ring if the

front panel is released.

2. Determine the appropriate position

where the holes on the bracket and
the side of the unit match.

3. Tighten two screws on each side.

• Use either truss screws (5 mm × 8 mm) or

flush surface screws (5 mm × 9 mm), depend-

ing on the shape of screw holes in the bracket.

Fastening the front panel

If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screw.

Note

• When this unit is installed in a vehicle without

ACC (accessory) position on the ignition switch,

red cable must be wired to the terminal that can

detect the operation of the ignition key. Otherwise,

battery drain may result.

ACC

ACC position

No ACC position

• Use this unit in other than the following condi-

tions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or malfunc-

tion, be sure to follow the directions below.

— Disconnect the negative terminal of the battery

before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhesive

tape around them where they lie against metal

parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker’s nega-

tive cables.

• Control signal is output through blue/white cable

when this unit is powered on. Connect it to an ex-

ternal power amp’s system remote control or the

vehicle’s auto-antenna relay control terminal (max.

300 mA, 12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna booster

power supply terminal.

• Never connect blue/white cable to external power

amp’s power terminal. Also, never connect it to

the power terminal of the auto antenna. Other-

wise, battery drain or malfunction may result.

• IP-BUS connectors are color-coded. Be sure to

connect connectors of the same color.

• Black cable is ground. This cable and other

product’s ground cable (especially, high-current

products such as power amp) must be wired sepa-

rately. Otherwise, fire or malfunction may result if

they are accidentally detached.

Dashboard

Mounting sleeve

Rubber bush

Screw

Trim ring

Dashboard or Console

Factory radio mounting bracket

Screw

CRD4246AS_inst.indd 1-4

2007/08/24 10:01:12