Rocketfish RF-RBWS02-01 Leaflet

1  Unpack the package contents
2  Enable the remote control battery
 

Remove the tab from the bottom of the remote control.

(skip this if you are not using batteries)

Note: You will need a Phillips screwdriver.

1  Unscrew the bottom cover (three screws).
2  Insert eight alkaline or rechargeable NiMH C batteries 

matching the +/- symbols as indicated. 

 

Note: This product will only recharge NiMH batteries. 
Do not try to charge any other batteries such as NiCad 
batteries in this product. 

3  Replace the cover and fasten the three screws.
4  Turn on the wireless speaker using the power switch on the top panel.

(if you are not using batteries, or if you want to charge the batteries)
1  Connect the AC power adapter to the wireless speaker 

and plug into an AC power outlet.

2  Turn on the wireless speaker using the power switch on 

the top panel.

 Note: If you are using NiMH rechargeable batteries, your 

batteries will recharge whenever the speaker is connected to a 
power outlet with the AC power adapter. If batteries are not 
fully charged, you should charge them for 16 hours before 
using the wireless speaker.

Remote control

Wireless speaker

AC power adapter
for wireless speaker

1  Turn on the wireless sender and wireless speaker. The power indicator LEDs should light 

steadily. If they are blinking you need to rejoin the wireless sender and wireless speaker. See the 
Establishing communication section above.

2  Play music from the audio device connected to your wireless sender and listen to it from the 

wireless speaker.

3  Adjust the volume level on your wireless speaker.

Your wireless speaker supports an easy-to-use stereo mode in case you use a second wireless 
speaker.
To join a second wireless speaker to the network in a stereo configuration:
1  Join the first wireless speaker to your network (if it is already connected, skip to step 2). If you 

are unsure how to do that refer to “Establishing communication” above.

2 Press the SOURCE button on the first wireless speaker to select the Rocketboost audio source 

you want to listen to.

3  Join the second wireless speaker to the network. See “Establishing communication” above.
4 Press the SOURCE button on the second wireless speaker to select the same Rocketboost audio 

source as the other wireless speaker. You will now have two mono speakers, indicated by the 
LED on the front panel of each device.

5  Select which wireless speaker you want to be the left speaker, then press and hold the Source 

button for five seconds. It will start blinking rapidly.

6  On the other wireless speaker, press and hold the Source button for five seconds. The Source 

indicator will blink rapidly and then turn solid. The 

Channel (L/R) LED indicators will then show 

the appropriate Left and Right indication for each speaker.

7  The wireless speaker automatically switches to Mono if only one wireless speaker is turned on; 

however, when the second wireless speaker is turned on, the stereo settings will take effect.

Wireless

speaker

Eight alkaline or 
rechargeable NiMH C 
batteries (not included)

Every Rocketboost network must contain 
one hub device, which helps devices join 
the network. The network can have only 
one hub, which you can enable using the 
hub switch on the back of all 
Rocketboost wireless senders and 
wireless sender/receivers. 

The RF-RBWS02-01 is a receiver and is 
not a hub device. To add this receiver to 
your Rocketboost network, you need to 
join it to your hub device.
Important: Hub devices must always 
have power for your network to operate. 
The hub device can be in standby 
(power-saving) mode, but must stay 
plugged in.

© 2011 BBY Solutions, Inc., All Rights Reserved. Distributed by Best Buy Purchasing, LLC, 7601 Penn Avenue South, Richfield, MN USA 55423-3645

ENGLISH 11-0481

Rocketboost technology can connect all audio devices throughout your home 
to form a home audio network. Rocketboost products include “senders,” which 
send audio streams, and “receivers,” which receive the audio. This lets you listen 
to music from your sender in other rooms, using your receiver.
The RF-RBWS02-01 is a Rocketboost receiver and you can listen to audio from 
any of your Rocketboost sender devices.
Rocketboost is expandable. Each Rocketboost receiver can select the audio 
from any sender in your Rocketboost audio network. You can set up your 
network to meet your specific needs. The illustration shows an example 
Rocketboost network.

1   If possible, bring your Rocketboost hub device and the new Rocketboost wireless speaker into 

the same room.

2  Press the Power button on the Rocketboost hub device to turn it on.
3  Press the Power button on your Rocketboost wireless speaker to turn it on.
4   Press and hold the Power button on the Rocketboost hub device for more 

than three seconds to put it into joining mode. The power indicator starts 
blinking rapidly and the unit will stay in joining mode for 30 seconds.

5   Press and hold the Power button on your Rocketboost wireless speaker for 

more than three seconds to put it into joining mode.

 

•  When successfully joined, the power indicator LEDs 
  on both products will stop blinking and stay on.

 

•  If joining fails after 30 seconds, the power indicator 
  LEDs will begin flashing at a slower rate. 
  If this occurs, repeat the above steps.

 

•  Repeat steps 1-5 for each additional Rocketboost 
  device you are adding to your network.

6  After the link is established, if the Source indicator on 

the wireless speaker is still not illuminated, make sure 
that your source is turned on.
For more instructions, see your User Guide.

BASS

Lights when 
speaker is 
receiving 
audio from 
sender

CHARGE

BASS

POWER /JOIN

CHANNEL
L - MONO - R

SOURCE

Power on 
indicator

Wireless speaker

Wireless sender