Qsc 120 VAC User Manual
Amplifier Current Draw—120 VAC
Idle
1/8 Power
1/3 Power
Full Power
Current draw at
idle or with
very low signal
level.
idle or with
very low signal
level.
8
Ω
4
Ω
2
Ω
25V-70V-100V
8
Ω
4
Ω
2
Ω
25V-70V-100V
8
Ω
4
Ω
2
Ω
25V-70V-100V
Model
Amperes
Amperes
Amperes
Amperes
Amperes
Amperes
Amperes
Amperes
Amperes
Amperes
Amperes
Amperes
Amperes
PL 218
0.8
4.9
7.7
11.9
7.3
11.6
18.4
12.1
20.5
33
PL 224
0.8
5
7.7
11.5
8.3
13.2
19.8
15.9
26.7
41.1
PL 230
0.9
5.9
9.2
13.2
10.5
16.8
24.6
20.4
34.3
52.3
PL 236
1
7.8
12.1
16.8
13.7
21.4
30.2
25.8
42.4
60
PL 3.4
0.9
6.4
10.8
16.5
11.5
20.5
32
24.9
42
69.1
PL 3.8X
*
*
*
*
*
*
*
*
*
*
PL 4.0
1
11
15.2
21.2
18.8
30.3
40
35.8
57.6
83.2
PL 6.0 II
2.5
10.3
15.5
23.8
19.3
35.1
47.4
39.3
67.5
104.7
PLX 1202
0.9
3.5
5.4
8.6
5.1
8.7
12.9
8.4
13.9
22.2
PLX 1602
0.9
5.1
8
11.9
7.6
12.1
18.2
12.6
21.2
32.2
PLX 2402
0.8
5
7.7
11.5
8.3
13.2
19.8
15.9
26.7
41.1
PLX 3002
0.9
5.9
9.2
13.2
10.5
16.8
24.6
20.4
34.3
52.3
PLX 3402
0.9
7.6
11.6
16.6
13.1
20.3
30.4
25.1
40.6
58.6
CX 302
0.9
3.5
5.4
8.6
5.1
8.7
12.9
8.4
13.9
22.2
CX 502
0.9
5.1
8
11.9
7.6
12.1
18.2
12.6
21.2
32.2
CX 702
0.8
5
7.7
11.5
8.3
13.2
19.8
15.9
26.7
41.05
CX 902
0.9
5.9
9.2
13.2
10.5
16.8
24.6
20.4
34.3
52.3
CX 1102
0.9
7.6
11.6
16.6
13.1
20.3
30.4
25.1
40.6
58.6
CX 302V
1
5.6
8
12
CX 602V
0.9
8.7
8.7
13
13
20.5
20.5
CX 1202V
1
7.7
11.9
11.9
12.5
19.2
19.2
25.2
38.7
38.7
CX 254
0.7
5.8
9.2
14.3
8.8
14.2
21.7
14.8
24
38.2
CX 404
0.7
8.1
12.4
nr
12.2
19.3
nr
21.7
33.4
nr
CX 204V
0.8
na
na
na
8.3
na
na
na
12.7
na
na
na
20.1
CX 168
0.6
6.4
10
nr
9.9
15.1
nr
16.6
26
nr
CX 108V
0.6
na
na
na
6.4
na
na
na
10.2
na
na
na
15.6
ISA 280
0.3
2.6
4.1
6.2
3.8
6.2
9.7
6.7
11
16.5
ISA 450
0.4
3.5
5.9
9.1
5.4
9
14
9.7
16.2
25.4
ISA 750
0.5
4.5
7
10.3
8.3
13.3
20.5
16.1
26.5
40.7
ISA 1350
1.2
6.4
10.1
14.5
12.5
20.1
30.6
25.5
42.2
65.7
ISA 300T
0.3
2.6
4.1
6.2
5.5
3.8
6.2
9.7
8.4
6.7
11
16.5
12.9
ISA 500T
0.4
3.5
5.9
9.1
6.9
5.4
9
14
12.7
9.7
16.2
25.4
19.1
ISA 800T
0.5
4.5
7
10.3
8.5
8.3
13.3
20.5
16.5
16.1
26.5
40.7
31.7
DCA 1222
0.9
3.5
5.4
8.6
5.1
8.7
12.9
8.4
13.9
22.2
DCA 1622
0.9
5.1
8
11.9
7.6
12.1
18.2
12.6
21.2
32.2
DCA 2422
0.8
5
7.7
11.5
8.3
13.2
19.8
15.9
26.7
41.1
DCA 3022
0.9
5.9
9.2
13.2
10.5
16.8
24.6
20.4
34.3
52.3
DCA 3422
0.9
7.6
11.6
16.6
13.1
20.3
30.4
25.1
40.6
58.6
DCA 1824
0.7
5.8
9.2
14.3
8.8
14.2
21.7
14.8
24
38.2
DCA 1644
0.7
8.1
12.4
nr
12.2
19.3
nr
21.7
33.4
nr
RMX 850
0.4
2.8
4.4
6.3
4.1
6.6
9.2
7.1
11.3
16.5
RMX 1450
0.4
3.7
6
9.3
5.4
9.6
14.7
9.7
16
24.9
RMX 1850HD
1.1
3.9
6.1
8.7
6.9
11.2
16.6
12.6
20.7
32
Current draw at full power is measured with a 1 kHz sine
wave. However, it does not represent any real-world
operating condition.
wave. However, it does not represent any real-world
operating condition.
Current draw at 1/3 of full power is measured with pink
noise as a signal. It approximates operating with music or
voice with very heavy clipping and a very compressed
dynamic range.
noise as a signal. It approximates operating with music or
voice with very heavy clipping and a very compressed
dynamic range.
Current draw at 1/8 of full power is measured with pink
noise as a signal. It approximates operating with music or
voice with light clipping and repesents the amplifier's
typical "clean" maximum level, without audible clipping.
Use these figures for typical maximum level operation.
noise as a signal. It approximates operating with music or
voice with light clipping and repesents the amplifier's
typical "clean" maximum level, without audible clipping.
Use these figures for typical maximum level operation.
Current draw is the amount of AC current an amplifier demands while it is operating. Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full power,
and full power, with all channels driven simultaneously. The figures shown on this sheet are for 120 VAC usage; for 230- and 100-volt operation, see the companion sheets. For typical usage,
use the idle and 1/8 power figures. Where an asterisk (*) appears, the data was not available at press time. The designations "na" and "nr" respectively mean "not applicable" to the particular
amplifier model and "not rated" for the particular load impedance.
and full power, with all channels driven simultaneously. The figures shown on this sheet are for 120 VAC usage; for 230- and 100-volt operation, see the companion sheets. For typical usage,
use the idle and 1/8 power figures. Where an asterisk (*) appears, the data was not available at press time. The designations "na" and "nr" respectively mean "not applicable" to the particular
amplifier model and "not rated" for the particular load impedance.