Digi Tech Control 2 Owner's Manual
Selecting Presets
To select a preset in 5 Patch or 10 Patch Mode, follow these steps:
Press one of the footswitches numbered 1-5 (footswitches numbered 1-
10 in 10 Patch Mode). The associated footswitch LED will light and the
preset name and number will appear in the Display.
To select another preset, press another of the footswitches numbered
1-5 (footswitches numbered 1-10 in 10 Patch Mode). The previous
footswitch LED will turn off and the newly pressed footswitch’s LED will
now light.
10 in 10 Patch Mode). The associated footswitch LED will light and the
preset name and number will appear in the Display.
To select another preset, press another of the footswitches numbered
1-5 (footswitches numbered 1-10 in 10 Patch Mode). The previous
footswitch LED will turn off and the newly pressed footswitch’s LED will
now light.
In 5 Patch Mode, as different presets are selected, different effect footswitch
LEDs (Footswitches 6-10) will turn on and off based on the status of these
effects in the active preset.
LEDs (Footswitches 6-10) will turn on and off based on the status of these
effects in the active preset.
Bypassing Presets
To bypass an active preset, press the active preset footswitch. The Display
will read BYPASS when the preset is bypassed and the preset footswitch you
will read BYPASS when the preset is bypassed and the preset footswitch you
bypassed from will remain lit (in 5 Patch Mode, the effects footswitches that
were on before bypassing will also remain lit). To return to the same preset
from bypass, press the lit preset footswitch again and the last preset loaded
will become active again.
were on before bypassing will also remain lit). To return to the same preset
from bypass, press the lit preset footswitch again and the last preset loaded
will become active again.
You can also change to another preset from bypass by pressing any non-lit
preset footswitch. In 5 Patch Mode, you can also turn any of the effects
(DISTORTION, CHORUS/FX, DELAY, REVERB) on or off when exiting bypass
by pressing one of these footswitches instead of a preset footswitch. This
will load the last active preset and turn the respective effect on or off as it is
loaded.
preset footswitch. In 5 Patch Mode, you can also turn any of the effects
(DISTORTION, CHORUS/FX, DELAY, REVERB) on or off when exiting bypass
by pressing one of these footswitches instead of a preset footswitch. This
will load the last active preset and turn the respective effect on or off as it is
loaded.
NOTE: Bypassing presets with the footswitches is not available if the Bounce
Back feature is enabled. Refer to the Bounce Back section on page 8 for
more information about the Bounce Back feature.
Back feature is enabled. Refer to the Bounce Back section on page 8 for
more information about the Bounce Back feature.
Turning Effects On or Off
In 5 Patch Mode, Footswitches 6-9 are programmed to turn on or off the
following effects in the active preset:
following effects in the active preset:
Footswitch 6 controls the Distortion on/off.
Footswitch 7 controls the Chorus/FX on/off.
Footswitch 8 controls the Delay on/off.
Footswitch 9 controls the Reverb on/off.
Footswitch 10 can also be programmed to turn on and off effects as
well. See page 11 for more information about assigning effect on/off and
parameters to the CONTROL footswitch).
Footswitch 7 controls the Chorus/FX on/off.
Footswitch 8 controls the Delay on/off.
Footswitch 9 controls the Reverb on/off.
Footswitch 10 can also be programmed to turn on and off effects as
well. See page 11 for more information about assigning effect on/off and
parameters to the CONTROL footswitch).
1.
2.
Control 2 Owner’s Manual
Using the Control 2 Remote Foot Controller