Lynx LHEM48NG Use & Care Manual
P a g e
| 18
TIME/PROG Zone: Blank
FLAME Zone: Blank
FLAME Zone: Blank
THERMOSTAT OFF LCD Displays:
o MODE Zone: THERMO and OFF is displayed
o ROOM /AIR TEMP Zone: Measured temperature is displayed
o SET TEMP Zone: SET TEMP is displayed
o Time of day is displayed
o ROOM /AIR TEMP Zone: Measured temperature is displayed
o SET TEMP Zone: SET TEMP is displayed
o Time of day is displayed
Air Temperature Limit Function:
When using the heater with the remote control transmitter, always keep the remote transmitter by your side, i.e., at the
same place that you are sitting. This will assure that the temperature and thermostat function will always be reading the
same temperature that you are experiencing. Do not leave the remote transmitter outside or exposed to the elements
when not in use. Do not leave the transmitter facing the sun, or in a place that allows the transmitter to measure the
temperature of the sun. This could falsely raise the ‘air’ temperature that the transmitter is reading. Once the ‘room’/air
temperature reaches 95F degrees, the system will automatically shut the heater off. When the heater is turned on in
either the MANUAL ON or THERMOSTAT ON mode, once the air temperature becomes 95 degrees, the heater will cycle
automatically to the MANUAL OFF mode. If the user turns the control back ON, and the air temperature is still 95F
degrees or greater, the transmitter will switch back to MANUAL OFF.
Thermostat Disable Feature:
If, after using your heater, you decide that you do not want to use the THERMOSTAT function, you can simplify your
system and disable this function on the remote transmitter. When the THERMOSTAT mode is disabled:
system and disable this function on the remote transmitter. When the THERMOSTAT mode is disabled:
o The Modes of operation will cycle between MANUAL ON and MANUAL OFF (omitting THERMO).
o Program Operation (described below) is also disabled.
o The SET TEMP zone will be blank.
o The air temperature will still be measured & displayed in the ROOM/AIR TEMP Zone.
o The TIME/PROG zone will continue to display the Clock and Day of week, but none of the icons
o Program Operation (described below) is also disabled.
o The SET TEMP zone will be blank.
o The air temperature will still be measured & displayed in the ROOM/AIR TEMP Zone.
o The TIME/PROG zone will continue to display the Clock and Day of week, but none of the icons
associated with Program Mode will be displayed.
To disable or re-enable the Thermostat, the transmitter must be in MANUAL OFF Mode, then press and hold the
SET TEMP Zone and the DOWN Button simultaneously for 10-seconds. The entire contents of the LCD screen
will flash 3-times (0.5-seconds OFF, 0.5-seconds ON) to indicate the change has been made.
SET TEMP Zone and the DOWN Button simultaneously for 10-seconds. The entire contents of the LCD screen
will flash 3-times (0.5-seconds OFF, 0.5-seconds ON) to indicate the change has been made.
Program Feature:
This feature is intended to allow the user to cycle the heater, on and off, based on time settings throughout the week.
This feature can allow programming for up to 4 days of the week, and includes thermostat settings. This is a highly
sophisticated feature, and is recommended only for those who plan to use their heater at given times during given days.
In most cases, this usage pattern is not recommended. However, for those whose needs for outdoor heating are
predictable, it may prove to be an advantage.
This feature can allow programming for up to 4 days of the week, and includes thermostat settings. This is a highly
sophisticated feature, and is recommended only for those who plan to use their heater at given times during given days.
In most cases, this usage pattern is not recommended. However, for those whose needs for outdoor heating are
predictable, it may prove to be an advantage.
To enter Program Setup, with remote turned to either ON or OFF, press and hold the TIME/PROG Zone for 5
seconds.
seconds.
Program OFF LCD Displays:
o MODE Zone: OFF