Maytag MHN30PDCWW Installation Instruction

J. Cd

J. 

 

J. 

 

J. 

 

 

J.

Cd 

 

C_ 

 

_d 

 

 

Ed 

 

g

Both coin and debit selected. Press the DELICATES 

AND KNITS button 3 consecutive times for this 

selection.
Coins selected, debit disabled. Press the 

DELICATES AND KNITS button 3 consecutive times 

for this selection.
PR models factory default to J._d. Debit Card 

selected, coins disabled. Press the DELICATES AND 

KNITS button 3 consecutive times to change this 

selection.
Enhanced Debit is self-selected when a Generation 

2 card reader is installed in the washer. The Ed 

option cannot be manually selected or deselected.
Press the WOOLENS button once to advance  

to next code.

L.  00

This option causes the customer display to show 

‘ADD’ or ‘AVAILABLE’ rather than the amount of 

money to add. (Used mainly in debit installations.)

L.
L.

00
PS 

g

Not Selected ‘OFF.’
Selected ‘ON.’ Press the DELICATES AND KNITS 

button once for this selection.
Press the WOOLENS button once to advance  

to next code.

n. CE

When selected, money held in escrow for  

30 minutes without further escrow or cycle activity 

will be cleared.

n
n

00
CE 

g

Not Selected ‘OFF’.
Selected ‘ON’. Press the DELICATES AND KNITS 

button once for this selection.
Press the WOOLENS button once to advance  

to next code.

r. 800 TOP SPIN SPEED RPM

r. 800 

 
 
 

g

This can be selected from the following spin 
speeds: 600 rpm, 750 rpm, 800 rpm, 1000  
(displays as 999) rpm. Step between speeds by 
pressing the PERM PRESS button. Factory default 
of 800 rpm.
Press the WOOLENS button once to advance  

to next code.

U. 00

U. 00 

 

 

g

This represents the penny increment price offset 

used in Generation 2 (Enhanced Debit) PR models. 

Choose from 0–4 pennies by pressing the PERM 

PRESS button.
Press the WOOLENS button once to advance  

to next code.

A1. 00

A1. 00 

 

 

g

This is the number of minutes of PREWASH. 

Choose 0 to disable the prewash or select between 

2 and 7 minutes by pressing the PERM PRESS 

button.
Press the WOOLENS button once to advance  

to next code.

A2. 03

A2. 03 

 

g

This is the number of minutes of final high speed 

spin. Choose from 3–8 minutes by pressing the 

PERM PRESS button.
Press the WOOLENS button once to advance  

to next code.

This is “VIEW ONLY” and cannot be cleared.
Press the WOOLENS button once to advance to next code. 

END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
PD Models:  

Reinstall access door.
PR Models:

1.  Unplug washer or disconnect power.
2.  Open console, reinsert plug into AA1, close console.
3.  Plug in washer or reconnect power.

SERVICE ACCESS CODE
This code can be entered to access service mode without 
removing the console. It only functions on washers set up for 0 
vend price without any Special Pricing set-up, and the Coin/Debit 
Option must be set to “J._d”. If the washer is not in failure mode, 
the door must be opened to proceed. Service Access Code 
contains 4 steps. Perform the following steps:

1.  Press the upper left button.
2.  Press the lower right button.
3.  Press the upper right button.
4.  Press the lower left button.

NOTE: If the Service Access Code procedure is not completed 
properly, as noted above, there is a 15 second delay before it can 
be attempted again.
There are 3 options to exit from the Service Mode:

1.  From Set-up Code 8, press button #1 for 4 seconds.
2.  Wait 2 minutes without touching any buttons (without  

diagnostic modes running).

3.  Power down the washer, then reapply power.

1 00

Represents the number  

of cycles in HUNDREDS

1 02 =

200

2 00

Represents the number  

of cycles in ONES

2 25 =

25

TOTAL CYCLES =

225

3 00

Number of dollars  

in HUNDREDS

3 01 = $100.00

4 00

Number of dollars in ONES 4 68 = $ 68.00

5 00

Number of CENTS

5 75 = $

.75

TOTAL = $168.75