Kingston Technology 4GB, 1333MHz, DDR3, ECC, Reg w/Parity CL9, DIMM Dual Rank, x4 w/Therm Sen KVR1333D3D4R9S/4G Data Sheet
Product codes
KVR1333D3D4R9S/4G
Memory Module Specifications
KVR1333D3D4R9S/4G
4GB 512M x 72-Bit PC3-10600
CL9 Registered w/Parity 240-Pin DIMM
CL9 Registered w/Parity 240-Pin DIMM
Kingston.com
Document No. VALUERAM0797-001.A00 05/20/09 Page 1
DESCRIPTION
This document describes ValueRAM’s 512M x 72-bit 4GB
(4096MB) DDR3-1333 CL9 SDRAM (Synchronous DRAM)
registered w/parity, dual-rank memory module, based on
thirty-six 256M x 4-bit DDR3-1333 FBGA components. The
SPD is programmed to JEDEC standard latency 1333Mhz
timing of 9-9-9 at 1.5V. This 240-pin DIMM uses gold contact
fingers and requires +1.5V. The electrical and mechanical
specifications are as follows:
(4096MB) DDR3-1333 CL9 SDRAM (Synchronous DRAM)
registered w/parity, dual-rank memory module, based on
thirty-six 256M x 4-bit DDR3-1333 FBGA components. The
SPD is programmed to JEDEC standard latency 1333Mhz
timing of 9-9-9 at 1.5V. This 240-pin DIMM uses gold contact
fingers and requires +1.5V. The electrical and mechanical
specifications are as follows:
FEATURES
• JEDEC standard 1.5V ± 0.075V Power Supply
• VDDQ = 1.5V ± 0.075V
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 6,7,8,9,10
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7(DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
• VDDQ = 1.5V ± 0.075V
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 6,7,8,9,10
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7(DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does
not allow seamless read or write [either on the fly using A12
or MRS]
not allow seamless read or write [either on the fly using A12
or MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE ≤ 95°C
• Asynchronous Reset
• PCB : Height 18.75mm, double sided component
• PCB : Height 18.75mm, double sided component
SPECIFICATIONS
CL(IDD)
9 cycles
Row Cycle Time (tRCmin)
49.5ns (min.)
Refresh to Active/Refresh
110ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin)
36ns (min.)
Power
3.960 W (operating)
UL Rating
94 V - 0
Operating Temperature
0° C to 85° C
Storage Temperature
-55° C to +100° C
Continued >>