Supermicro C2SBA+II User Manual

Page of 133
Manual Revision: Rev. 1.1b
Release Date: March 6, 2009
Unless you request and receive written permission from Super Micro Computer, Inc., you may not 
copy any part of this document.
Information in this document is subject to change without notice.  Other products and companies 
referred to herein are trademarks or registered trademarks of their respective companies or mark 
holders.
Copyright © 2009 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.  
The vendor assumes no responsibility for any inaccuracies that may be contained in this document, 
makes no commitment to update or to keep current the information in this manual, or to notify any 
person  or  organization  of  the  updates.    Please  Note:    For  the  most  up-to-date  version  of  this 
manual, please see our web site at www.supermicro.com.
Super  Micro  Computer,  Inc.  ("Supermicro")  reserves  the  right  to  make  changes  to  the  product 
described  in  this  manual  at  any  time  and  without  notice.   This  product,  including  software,  if  any, 
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or 
reduced to any medium or machine without prior written consent.
IN  NO  EVENT  WILL  SUPER  MICRO  COMPUTER,  INC.  BE  LIABLE  FOR  DIRECT,  INDIRECT, 
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE 
USE  OR  INABILITY  TO  USE  THIS  PRODUCT  OR  DOCUMENTATION,  EVEN  IF  ADVISED  OF 
THE  POSSIBILITY  OF  SUCH  DAMAGES.    IN  PARTICULAR,  SUPER  MICRO  COMPUTER,  INC. 
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED 
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, 
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.   
 
 
 
 
 
 
 
 
 
 
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa 
Clara County in the State of California, USA.  The State of California, County of Santa Clara shall 
be  the  exclusive  venue  for  the  resolution  of  any  such  disputes.    Super  Micro's  total  liability  for  all 
claims will not exceed the price paid for the hardware product.   
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B 
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection  against  harmful  interference  in  a  residential  installation.  This  equipment  generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the 
manufacturer’s  instruction  manual,  may  cause  interference  with  radio  communications.  However, 
there  is  no  guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment 
does  cause  harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by 
turning  the  equipment  off  and  on,  you  are  encouraged  to  try  to  correct  the  interference  by  one 
or more of the following measures:  
 
 
 
 
 
Reorient or relocate the receiving antenna. 
 
 
 
 
 
Increase the separation between the equipment and the receiver. 
 
 
 
Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is 
connected.  
 
 
 
 
 
 
 
Consult the dealer or an experienced radio/television technician for help.
California  Best  Management  Practices  Regulations  for  Perchlorate  Materials:  This  Perchlorate 
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate 
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.   
 
 
 
 
 
 
 
 
 
WARNING: Handling of lead solder materials used in this 
product  may  expose  you  to  lead,  a  chemical  known  to 
the  State  of  California  to  cause  birth  defects  and  other 
reproductive harm.