Gaggenau VK414610 Installation Instruction
12
2
Evenly insert the unit in the cut-out. Press the unit
firmly into the cut-out from above.
firmly into the cut-out from above.
Note: The unit must sit firmly in the cut-out and
must not move (e.g. during cleaning). If
necessary, secure strips at the sides in the cut-
out if the cut-out width is at the top tolerance
limit.
must not move (e.g. during cleaning). If
necessary, secure strips at the sides in the cut-
out if the cut-out width is at the top tolerance
limit.
3
Connect the appliance to the mains and check
that it is working. If both illuminated rings behind
the control knobs flash alternately, the connecting
cable between the control console and the
appliance is not plugged in. Check that the
connecting cable is fitted correctly.
that it is working. If both illuminated rings behind
the control knobs flash alternately, the connecting
cable between the control console and the
appliance is not plugged in. Check that the
connecting cable is fitted correctly.
4
Flush installation only : it is imperative to test
functioning before jointing!
functioning before jointing!
Joint the surrounding
gap with a suitable, temperature-resistant silicone
adhesive (such as OTTOSEAL
adhesive (such as OTTOSEAL
®
S 70). Smoothen
the seal joint with smoothing agent recommended
by the manufacturer. Observe the notes on
processing the silicone adhesive. Do not operate
the appliance until the silicone adhesive has dried
completely (at least 24 hours, depending on room
temperature).
by the manufacturer. Observe the notes on
processing the silicone adhesive. Do not operate
the appliance until the silicone adhesive has dried
completely (at least 24 hours, depending on room
temperature).
NOTICE: Unsuitable silicone adhesive used on
natural stone worktops will cause permanent
discoloration.
natural stone worktops will cause permanent
discoloration.
Connect Electrical Supply
Refer to data plate for more information. See "Service"
for data plate location.
for data plate location.
The branch-circuit breakers ampacity, the wire sizes
and the connections must be conform to the
requirements of the National Electrical Code or
Canadian Electrical Code and all local codes and
ordinances.
and the connections must be conform to the
requirements of the National Electrical Code or
Canadian Electrical Code and all local codes and
ordinances.
Attach flexible conduit to the junction box. Connect
the lead wires to the junction box supply wires in
proper phase:
the lead wires to the junction box supply wires in
proper phase:
▯
black (L1) to black
▯
red (L2) to red
▯
green to ground
The mains connecting cable must at least correspond
to the type SJTO 3x16 AWG 105°C. The mains
connecting cable must only be purchased through and
connected by an authorised specialist.
to the type SJTO 3x16 AWG 105°C. The mains
connecting cable must only be purchased through and
connected by an authorised specialist.
Connection with a plug
▯
Plug has to be conform with NEMA
CONFIGURATIONS FOR PLUGS AND
RECEPTACLES.
CONFIGURATIONS FOR PLUGS AND
RECEPTACLES.
▯
The appliance must be properly grounded.
▯
Plug must be rated not less than type 6-20 P (2-
pole 3-wire grounding).
pole 3-wire grounding).
▯
Only a qualified electrician should connect the
plug.
plug.
▯
Install a socket outlet earthed in accordance with
regulations approx. 27" (70 cm) above the floor
behind the appliance. The socket outlet must still
be accessible after installation.
regulations approx. 27" (70 cm) above the floor
behind the appliance. The socket outlet must still
be accessible after installation.
Check the Installation
9
WARNING
Before you plug in an electrical cord or turn on
power supply, make sure all controls are in the
OFF position.
power supply, make sure all controls are in the
OFF position.
Remove everything from the cooktop surface.
Switch on the circuit breaker.
Verify that elements function properly.
Removing appliance
Disconnect the appliance from the power supply. For
flush-mounted appliances, remove the silicone joint.
Push out the appliance from below.
flush-mounted appliances, remove the silicone joint.
Push out the appliance from below.
9
CAUTION
Damage to appliance! Don't lever device out
from above at the frame.
from above at the frame.