Monogram ZDT800SIFII Installation Instruction

 35(7(67&+(&./,67

•  Check to be sure power is OFF.
•  Open door and remove all foam and paper packaging.
•  Locate the Owner’s Manual set aside in Step 1.
•  Read the Owner’s Manual for operating instructions.
•  Check door opening and closing. If door does not open 

and close freely, check for proper routing of spring cable 
over pulley. If door drops or closes when released, adjust 
spring tension. See Step 2.

•  Check to be sure that wiring is secure under the 

dishwasher, not pinched or in contact with door springs or 
other components. See Step 19.

•  Check door alignment with tub. If door hits tub, level 

dishwasher. See Step 15.

•  Check door alignment with cabinet. If door hits cabinet, 

reposition dishwasher. See Step 14.

•  Check that door spring does not contact water line, fill 

hose, wiring or other components. See Step 14.

•  Verify water supply and drain lines are not kinked or in 

contact with other components. Contact with motor or 
dishwasher frame could cause noise. 

•  Turn on the sink hot water faucet and verify water 

temperature. Incoming water temperature must 
be between 120°F and 140°F. A minimum of 120°F 
temperature is required for best wash performance. See 
“Prepare Hot Water Line,” page 5.

•  Add 1 quarts of water to the bottom of the dishwasher to 

lubricate the pump seal.

•  Turn on water supply. Check for leaks. Tighten 

connections if needed.

•  Remove protective film if present from the control panel 

and door.

  STEP 21  ',6+:$6+(5:(77(67

•  Turn on power supply or plug power cord into outlet, if 

equipped.

•  Select a cycle to run and push the START button.
•  Ensure the door is latched. Dishwasher should start.
•  Check to be sure that water enters the dishwasher. If 

water does not enter the dishwasher, check to be sure 
that water and power are turned on.

•  Check for leaks under the dishwasher. If a leak is found, 

turn off power at the breaker, and then tighten water 
connections. Restore power after leak is corrected.

•  Check for leaks around the door. A leak around the door 

could be caused by door rubbing or hitting against  
adjacent cabinets. Reposition the dishwasher if necessary. 
See Step 14.

•  Press and hold the START button for 3 seconds to cancel 

the cycle. The unit will begin to drain. Check drain lines. If 
leaks are found, turn off power at the breaker and correct 
plumbing as necessary. Restore power after corrections 
are made. See Steps 8, 10, 11 and 18.

•  Open dishwasher door and make sure all of the water 

has drained. If not, check that disposer plug has been 
removed and/or air gap is not plugged. Also check drain 
hose to be sure it is not kinked underneath or behind 
dishwasher. See Step 18.

• Press START button once again and run dishwasher through 

another cycle. Check for leaks and correct if required.

•  Repeat this step as necessary.

• Slide Floor Protect under dishwasher.
• Angle the rear back edge of the Floor Protect upwards to 

engage mounting tabs.

• Lift front of drip tray and secure with 2 screws.
• Connect leak sensor connector to leak sensor.

Floor Protect

Leak sensor

:KHQUHLQVWDOOLQJWKHÀRRUSURWHFWSDQPDNHFHUWDLQWKDW

the screws have been fully secured. This will ensure that 
LIWKHXQLWLVSURSHUO\JURXQGHGWKDWWKHÀRRUSURWHFWSDQ

will also be grounded.