Electrolux EIFLS60JIW Use & Care Manual
28
Solutions to Common Problems
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
NOISE
High pitch “jet engine”
noise.
noise.
A certain amount of motor whine is nor-
mal during the spin cycle.
mal during the spin cycle.
Rattling and clanking
noise.
noise.
Foreign objects such as coins or safety
pins may be in drum or pump.
pins may be in drum or pump.
Stop washer and check drum. If noise continues after
washer is restarted, objects may be in pump. Call your
authorized servicer.
washer is restarted, objects may be in pump. Call your
authorized servicer.
Belt buckles and metal fasteners are hit-
ting wash drum.
ting wash drum.
To prevent unnecessary noise and damage to drum,
fasten fasteners and turn items inside out.
fasten fasteners and turn items inside out.
Thumping sound.
Heavy wash loads may produce a
thumping sound. This is usually normal. If
sound continues, washer is probably out
of balance.
thumping sound. This is usually normal. If
sound continues, washer is probably out
of balance.
Stop washer and redistribute wash load.
Vibrating noise.
Washer is not resting fi rmly on fl oor.
Move washer so it rests fi rmly on fl oor. Adjust leveling
legs. See INSTALLATION INSTRUCTIONS for details.
legs. See INSTALLATION INSTRUCTIONS for details.
Shipping bolts and foam block have not
been removed during installation.
been removed during installation.
See INSTALLATION INSTRUCTIONS for removing ship-
ping bolts and foam block.
ping bolts and foam block.
Wash load unevenly distributed in drum.
Stop washer and rearrange wash load.
OPERATING
Washer does not start.
Electrical power cord may not be plugged
in or connection may be loose.
in or connection may be loose.
Make sure plug fi ts tightly in wall outlet.
House fuse blown, circuit breaker
tripped, or a power outage has occurred.
tripped, or a power outage has occurred.
Reset circuit breaker or replace fuse. Do not increase
fuse capacity. If problem is a circuit overload, have
it corrected by a qualifi ed electrician. If problem is a
power outage, call local electric company.
fuse capacity. If problem is a circuit overload, have
it corrected by a qualifi ed electrician. If problem is a
power outage, call local electric company.
Water supply faucets are not turned on.
Turn on water supply faucets.
Motor is overheated. Washer motor will
stop if it becomes overheated.
stop if it becomes overheated.
It will automatically restart after a cool down period
of up to 30 minutes (if washer has not been manually
turned off).
of up to 30 minutes (if washer has not been manually
turned off).
Washer door is not completely closed.
Close door completely.
Washer won’t spin.
Load is too small.
Add 1 or 2 similar items to help balance the load.
Residue left in drum.
Heavily soiled items.
Wipe drum with a nonabrasive household cleanser, then
rinse. Shake or brush excess dirt and sand from items
before washing
rinse. Shake or brush excess dirt and sand from items
before washing
LCD displays
DEMO MODE
.
Washer has been programmed to tempo-
rarily perform a repeating demo cycle.
rarily perform a repeating demo cycle.
To return to the factory default settings, select RESET
in set prefs under the options scroll buttons.
in set prefs under the options scroll buttons.
Door hesitates to open
after pressing Touch-2-
Open latch.
after pressing Touch-2-
Open latch.
Water on bellows may have dried, leaving
residue on door glass during extended
non-use or vacation.
residue on door glass during extended
non-use or vacation.
Clean residue from door glass and wipe front of bellows
opening with warm water and soap.
opening with warm water and soap.
If issue persists, wipe front of bellows opening with
Lemon Pledge
Lemon Pledge
®
spray or wipes.
Service Prevention Checklist
Before calling for service, review this list. It may save both time and expense. The list includes common
occurrences that are not the result of defective workmanship or materials in this washer.
occurrences that are not the result of defective workmanship or materials in this washer.