BlueStar BSPC48240TS Owner's Manual
HANDLING
REMOVE ALL WATCHES, BELT BUCKLES, JEWELRY, RINGS AND ANY CLOTHING WITH
METAL BUTTONS OR SNAPS TO PREVENT DAMAGE TO THE HOOD.
METAL BUTTONS OR SNAPS TO PREVENT DAMAGE TO THE HOOD.
WHEN YOU BEGIN THE INSTALLATION PROCESS REMOVE THE HOOD FROM IT’S ORIGI-
NAL CARTON AND PLACE THE HOOD ON A CLEAN, NON-ABRASIVE BLANKET.
NAL CARTON AND PLACE THE HOOD ON A CLEAN, NON-ABRASIVE BLANKET.
INSPECT THE HOOD CAREFULLY FOR ANY DAMAGE OR IMPERFECTIONS BEFORE YOU
BEGIN TO INSTALL THE HOOD. IF ANY DAMAGE OR IMPERFECTIONS EXIST, RECARTON
THE HOOD AND CALL YOUR DEALER IMMEDIATELY, DO NOT INSTALL A DAMAGED
HOOD.
BEGIN TO INSTALL THE HOOD. IF ANY DAMAGE OR IMPERFECTIONS EXIST, RECARTON
THE HOOD AND CALL YOUR DEALER IMMEDIATELY, DO NOT INSTALL A DAMAGED
HOOD.
IT IS HIGHLY RECOMMENDED THAT RUBBER GLOVES BE USED TO PREVENT
SCRATCHES ON THE HOOD AND TO PROVIDE YOU WITH A FIRM GRIP.
SCRATCHES ON THE HOOD AND TO PROVIDE YOU WITH A FIRM GRIP.
WHEN REMOVING THE HOOD FROM THE CARTON LOCATE THE FILTERS. THE FILTERS
ARE PACKED SEPARATELY.
ARE PACKED SEPARATELY.
DO NOT REMOVE HOOD FROM ORIGINAL CARTON UNTIL YOU ARE READY TO IN-
STALL
UNPACKING
CHECK THE PACKAGE FOR DAMAGE. IF ANY DAMAGE IS VISIBLE YOU SHOULD MARK
THE BILL OF LADING YOU SIGN THAT THERE MAY BE CONCEALED DAMAGE.
THE BILL OF LADING YOU SIGN THAT THERE MAY BE CONCEALED DAMAGE.
INSURE THE CONTAINER IS UPRIGHT. IF THE CONTAINER IS NOT UPRIGHT MAJOR DAM-
AGE CAN OCCUR TO YOUR APPLIANCE. IF DAMAGE IS DISCOVERED, DO NOT REFUSE
DELIVERY. CONTACT THE DEALER AND FILE APPROPRIATE FREIGHT CLAIMS. SAVE
ALL PACKAGING MATERIAL. DO NOT CONTACT THE MANUFACTURER. YOUR APPLI-
ANCE WAS SHIPPED FROM THE DEALER YOU PURCHASED IT FROM. SHIPPING DAMAGE
CLAIMS ARE TO BE RESOLVED BETWEEN THE CUSTOMER, SHIPPING CARRIER AND
DEALER. THE MANUFACTURER MAY ASSIST IN RESOLVING ANY SUCH CLAIMS, BUT
SUCH ASSISTANCE DOES NOT RELIEVE YOU OF YOUR RESPONSIBILITY.
AGE CAN OCCUR TO YOUR APPLIANCE. IF DAMAGE IS DISCOVERED, DO NOT REFUSE
DELIVERY. CONTACT THE DEALER AND FILE APPROPRIATE FREIGHT CLAIMS. SAVE
ALL PACKAGING MATERIAL. DO NOT CONTACT THE MANUFACTURER. YOUR APPLI-
ANCE WAS SHIPPED FROM THE DEALER YOU PURCHASED IT FROM. SHIPPING DAMAGE
CLAIMS ARE TO BE RESOLVED BETWEEN THE CUSTOMER, SHIPPING CARRIER AND
DEALER. THE MANUFACTURER MAY ASSIST IN RESOLVING ANY SUCH CLAIMS, BUT
SUCH ASSISTANCE DOES NOT RELIEVE YOU OF YOUR RESPONSIBILITY.
MOVE THE CONTAINER AS CLOSE TO ITS INSTALLATION LOCATION AS POSSIBLE. THIS
WILL REDUCE MOVING AND HANDLING YOUR APPLIANCE ONCE IT IS OUT OF ITS SHIP-
PING CONTAINER
WILL REDUCE MOVING AND HANDLING YOUR APPLIANCE ONCE IT IS OUT OF ITS SHIP-
PING CONTAINER
DO NOT DISCARD PACKAGING WITHOUT FIRST LOCATING THE FILTERS
INSPECT ALL MOLDED PACKAGING BEFORE DISCARDING
ANY DAMAGE MUST BE REORTED BEFORE INSTALLING THE HOOD.
ONCE THE HOOD HAS BEEN INSTALLED, NO RETURN WILL BE AC-
CEPTED!
ONCE THE HOOD HAS BEEN INSTALLED, NO RETURN WILL BE AC-
CEPTED!
P/N 750306 Page 7
MAKE SURE BLOWERS ARE FREE FROM OBSTRUCTIONS (PACKING AND DEBRIS). TEST
RUN BLOWERS BEFORE FINALIZING INSTALLATION. CHECK WITH MANUFACTURER BE-
FORE ATTEMPTING TO USE OTHER THAN BLUESTAR BLOWER SYSTEMS. FOR TECHNI-
CAL INFORMATION CONTACT BLUESTAR SERVICE (800-449-8691)
RUN BLOWERS BEFORE FINALIZING INSTALLATION. CHECK WITH MANUFACTURER BE-
FORE ATTEMPTING TO USE OTHER THAN BLUESTAR BLOWER SYSTEMS. FOR TECHNI-
CAL INFORMATION CONTACT BLUESTAR SERVICE (800-449-8691)