Alpine INE-W940 Owner's Manual
36
-EN
You can set the Subwoofer level when a Subwoofer is connected.
Setting item: SubW. LEVEL
Setting contents: 0 to 15 (Initial setting: 0)
Setting contents: 0 to 15 (Initial setting: 0)
• If the Subwoofer setting is “Off,” the setting cannot be set.
Touch [Sub W. LEVEL 0] to lower the Subwoofer level
to Level 0.
to Level 0.
• To return to the previous Subwoofer level, touch [Sub W. LEVEL 0]
again.
The subwoofer output phase is toggled Subwoofer Normal (0°) or
Subwoofer Reverse (180°).
Subwoofer Reverse (180°).
Setting item: SubW. Phase
Setting contents: 0° / 180° (Initial setting: 0°)
Setting contents: 0° / 180° (Initial setting: 0°)
• If the Subwoofer setting is “Off,” the setting cannot be set.
Adjusting the Time Correction (TCR)
[TCR] is selected on the Sound setup menu in step 3. Refer to “Sound
Setup Operation” (page 34).
Before performing the following procedures, refer to “About Time
Correction” (page 38).
Setup Operation” (page 34).
Before performing the following procedures, refer to “About Time
Correction” (page 38).
Setting item: Time Correction
1
Touch [ms] or [cm] to select mode for making
adjustments.
adjustments.
Each time you touch, the onscreen button and correction
mode changes.
mode changes.
ms: Adjust time.
cm: Adjust listening position and distance from each speaker.
cm: Adjust listening position and distance from each speaker.
2
Touch [
] or [
] for each speaker to adjust the
time or distance.
0.0msec to 9.9msec (0.1msec/step)
0.0cm to 336.6cm (3.4cm/step)
All speaker setting values are adjustable in the range of 15ms or
510cm.
0.0cm to 336.6cm (3.4cm/step)
All speaker setting values are adjustable in the range of 15ms or
510cm.
3
To store the adjusted setting value, touch and hold
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
• Touch [Flat] to set all values to 0.0.
• If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot
• If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot
be edited (Refer to page 38).
• If the Subwoofer setting is “Off,” the Subwoofer setting cannot be
edited (Refer to page 38).
Calling the Time Correction Value
Calling the pre-set time correction value.
Touch [Preset1], [Preset2], or [Preset3] on the time
correction screen.
correction screen.
The setting stored in the Preset will be recalled.
Adjusting the Crossover Settings (X-
OVER)
OVER)
[X-OVER] is selected on the Sound setup menu in step 3. Refer to
“Sound Setup Operation” (page 34).
Before performing the following procedures, refer to “About the
Crossover” (page 39).
“Sound Setup Operation” (page 34).
Before performing the following procedures, refer to “About the
Crossover” (page 39).
Setting item: X-OVER
1
Touch [Channel] to select the channel.
Each time you touch, the channel switches.
• The channel being adjusted is displayed in red.
2
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [
] or [
] of “Freq.,” then select the cut-off
frequency.
Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) /
100 / 125 / 160 / 200 Hz
Adjusting the Slope
Touch [
] or [
] of “Slope,” then adjust the HPF or LPF
slope.
Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct
Adjusting the Level
Touch [
] or [
] of “Level,” then adjust the HPF or LPF
level.
Setting contents: -12 to 0 dB (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
channels.
Adjusting the Subwoofer Level
Lowering Subwoofer Level Temporarily
Setting the Subwoofer Phase
Correction mode
Front HPF
Rear HPF
Subw. LPF