Bosch d9412gv3 User Manual
D9412GV3/D7412GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters
EN | 34
Bosch Security Systems, Inc. | 10/11 | F01U170807-02
RPS Call Back
Default:
No
Selection: Yes or No
Yes
When the control panel hears the
correct RPS passcode, it hangs up
the phone, seizes the phone line,
then dials the programmed RPS
phone number (refer to the RPS Ph
prompt on page 35). This ensures
that the control panel only
communicates with RPS units
connected to the programmed phone
number.
correct RPS passcode, it hangs up
the phone, seizes the phone line,
then dials the programmed RPS
phone number (refer to the RPS Ph
prompt on page 35). This ensures
that the control panel only
communicates with RPS units
connected to the programmed phone
number.
If the call is answered manually, the
call back must be initiated manually.
call back must be initiated manually.
No
The RPS session starts immediately.
No call back is required. The control
panel can engage in RPS sessions
when called from any phone number
and a proper RPS passcode is
identified.
No call back is required. The control
panel can engage in RPS sessions
when called from any phone number
and a proper RPS passcode is
identified.
This function allows the control panel, after it verifies
the RPS passcode, to provide an additional level of
security by hanging up and dialing the RPS phone
number at the central station before allowing any
upload or download.
the RPS passcode, to provide an additional level of
security by hanging up and dialing the RPS phone
number at the central station before allowing any
upload or download.
When using the RPS Call Back feature,
be sure to program the character “C” as
the last digit in the RPS phone number
when using DTMF Dialing.
be sure to program the character “C” as
the last digit in the RPS phone number
when using DTMF Dialing.
RPS Line Monitor
Default:
Yes
Selection: Yes or No
Yes
Allows the control panel to
communicate with RPS after the
answering machine answers the
phone.
communicate with RPS after the
answering machine answers the
phone.
No Use
No if the control panel does not
share the phone line with an
answering machine.
answering machine.
This program item enables a control panel that
shares a phone line with an answering machine to
communicate with RPS at the central station, even
though the answering machine answers the phone.
You must program Answer Armed or Answer
Disarmed. The control panel must be in the correct
armed state.
shares a phone line with an answering machine to
communicate with RPS at the central station, even
though the answering machine answers the phone.
You must program Answer Armed or Answer
Disarmed. The control panel must be in the correct
armed state.
Program this item No if it causes false
seizures of the phone line or if you do
not use RPS. This indicates that a
device using the same frequency tone is
also using the phone line to which the
control panel is connected.
seizures of the phone line or if you do
not use RPS. This indicates that a
device using the same frequency tone is
also using the phone line to which the
control panel is connected.
If RPS Call Back is programmed Yes,
the control panel hangs up the phone
after the RPS tone and a proper RPS
passcode is identified. It then calls the
RPS phone number.
the control panel hangs up the phone
after the RPS tone and a proper RPS
passcode is identified. It then calls the
RPS phone number.
Answer Armed
Default:
Refer to the program record sheet
Selection: 0 to 15
0 No
answer.
1 to 15
The control panel answers the phone
after the specified number of rings
when all areas are master armed.
after the specified number of rings
when all areas are master armed.
Set the telephone ring counter to answer when all
areas are master armed. If any area in the control
panel is perimeter armed or disarmed, the Answer
Disarmed ring counter is used.
areas are master armed. If any area in the control
panel is perimeter armed or disarmed, the Answer
Disarmed ring counter is used.
For the purposes of answering the RPS
phone call, the control panel considers
Perimeter Armed a disarmed state..
phone call, the control panel considers
Perimeter Armed a disarmed state..
Answer Disarmed
Default:
Refer to the program record sheet
Selection:
0 to 15
0 No
answer.
1 to 15
The control panel answers the
phone after the specified number of
rings when any area in the system is
in a perimeter armed or disarmed
state.
phone after the specified number of
rings when any area in the system is
in a perimeter armed or disarmed
state.
Set telephone ring counter to answer when any area is
in a perimeter armed or disarmed state.
in a perimeter armed or disarmed state.
For the purposes of answering the RPS
phone call, the control panel considers
Perimeter Armed a disarmed state.
phone call, the control panel considers
Perimeter Armed a disarmed state.