Bosch d9412gv3 User Manual
D9412GV3/D7412GV3 | Program Entry Guide | 3.0 Points
EN | 96
Bosch Security Systems, Inc. | 10/11 | F01U170807-02
P## Watch Point
Default:
Refer to the program record sheet
Selection: Yes or No
Yes
Yes
Activates Watch Mode responses if
the point is faulted while the control
panel is in Watch Mode.
the point is faulted while the control
panel is in Watch Mode.
No
Does not activate Watch Mode
responses for this point.
responses for this point.
Use this option to allow a Controlled point to generate
a watch tone while the area is disarmed and not
faulted to a trouble or alarm condition.
a watch tone while the area is disarmed and not
faulted to a trouble or alarm condition.
P## Relay Response Type
Default:
Refer to the program record sheet
Selection: 0 to 2
0
0
Point state does not affect the
operation of the corresponding relay.
operation of the corresponding relay.
1
Relay Follows Point: The relay
corresponding with this point
activates when the point is faulted to
any off-normal condition, even if the
point is bypassed. The relay
automatically resets when the point
returns to normal.
corresponding with this point
activates when the point is faulted to
any off-normal condition, even if the
point is bypassed. The relay
automatically resets when the point
returns to normal.
2
Relay Latches: The relay
corresponding with this point latches
when the point enters into an alarm
condition. This relay provides a
steady output until the alarm is
acknowledged by a valid passcode,
then cleared from alarm memory with
an acknowledgment from the keypad.
corresponding with this point latches
when the point enters into an alarm
condition. This relay provides a
steady output until the alarm is
acknowledged by a valid passcode,
then cleared from alarm memory with
an acknowledgment from the keypad.
Use this option to cause a relay (1 to 127 for
D9412GV3; 1 to 64 for D7412GV3) to respond when
a corresponding point with the same number (1 to
127) is faulted. This requires connecting D8129
OctoRelays to Zonex Bus 1 and Zonex Bus 2
(D9412GV3 only). Refer to the address settings on
the back of the D9412GV3/D7412GV3 Program
Record Sheet (P/N: F01U170809).
D9412GV3; 1 to 64 for D7412GV3) to respond when
a corresponding point with the same number (1 to
127) is faulted. This requires connecting D8129
OctoRelays to Zonex Bus 1 and Zonex Bus 2
(D9412GV3 only). Refer to the address settings on
the back of the D9412GV3/D7412GV3 Program
Record Sheet (P/N: F01U170809).
Point 128 is reserved for use other than
an actual point. Only the first 127 points
can have an associated relay. Relays are
not available for Points 129 to 247.
an actual point. Only the first 127 points
can have an associated relay. Relays are
not available for Points 129 to 247.
Do not use the Change Relays? function
to toggle relays reserved for special
functions. Special function relays are
Area and Panel Wide Relay functions as
well as relays assigned to CC## Enter
Key Relay and P## Relay Response
Type.
to toggle relays reserved for special
functions. Special function relays are
Area and Panel Wide Relay functions as
well as relays assigned to CC## Enter
Key Relay and P## Relay Response
Type.
P## Display as Device
Default:
No
Selection: Yes or No
Yes
Yes
Display CHECK DEVICE when this
point is off-normal.
point is off-normal.
No
Do not display CHECK DEVICE
when this point is off-normal.
when this point is off-normal.
Use P## Display as Device to cause the keypad to
display CHECK DEVICE when a point is off-normal or
is acknowledged after going into alarm.
display CHECK DEVICE when a point is off-normal or
is acknowledged after going into alarm.
Use this function for devices with a dry
contact output that faults a point when
the device is in a trouble condition.
contact output that faults a point when
the device is in a trouble condition.
P## Local While Disarmed
Default:
Refer to the program record sheet
Selection: Yes or No
Yes
Yes
Suppress Alarm, Trouble and
Restoral* Reports from this point
while the area to which it is assigned
is disarmed.
Restoral* Reports from this point
while the area to which it is assigned
is disarmed.
No
Send event reports occurring from
this point while the area is disarmed.
this point while the area is disarmed.
* Transmission of Restoral Reports continues if the alarm,
trouble, or bypass (by Sked, RPS, or Swinger bypass)
condition occurred when the area disarmed, and the point
restored.
condition occurred when the area disarmed, and the point
restored.
To meet UL 864 requirements for
Central Station and Remote Station
applications, set this parameter to No.
Central Station and Remote Station
applications, set this parameter to No.
Use this option to allow a Controlled point (P## Type
1, 2, 3), to report Alarms, Troubles, and Restoral
Reports only when the area is armed. This prompt
does not affect local annunciation.
1, 2, 3), to report Alarms, Troubles, and Restoral
Reports only when the area is armed. This prompt
does not affect local annunciation.