Neumann.Berlin M 149 Tube User Manual
6
7
M 149 Tube
Nach wenigen Minuten hat die Röhre im M 149 Tube
ihren stabilen Betriebszustand erreicht und weist
dann ihren besonders niedrigen Eigengeräuschpe-
gel auf.
ihren stabilen Betriebszustand erreicht und weist
dann ihren besonders niedrigen Eigengeräuschpe-
gel auf.
Beim Umschalten der Richtcharakteristik tritt für
einen Zeitraum bis ca. 30 s ein erhöhter Rausch-
pegel auf. Dieser entsteht durch die Umladung der
Kapsel auf die jeweils notwendige Vorspannung.
einen Zeitraum bis ca. 30 s ein erhöhter Rausch-
pegel auf. Dieser entsteht durch die Umladung der
Kapsel auf die jeweils notwendige Vorspannung.
Eine eventuell anliegende externe Phantomspei-
sung beeinträchtigt die Funktion des M 149 Tube
nicht. Wird eine externe Phantomspeisung an- oder
abgeschaltet, ergibt sich kurzzeitig ein leicht er-
höhter Eigengeräuschpegel.
sung beeinträchtigt die Funktion des M 149 Tube
nicht. Wird eine externe Phantomspeisung an- oder
abgeschaltet, ergibt sich kurzzeitig ein leicht er-
höhter Eigengeräuschpegel.
Der Netzschalter des Netzgerätes unterbricht die
Zuleitungen des eingebauten Netzteiles sekundär-
seitig. Zur Stromersparnis sollte das Netzgerät bei
längerer Nichtbenutzung vom Stromnetz getrennt
werden.
Zuleitungen des eingebauten Netzteiles sekundär-
seitig. Zur Stromersparnis sollte das Netzgerät bei
längerer Nichtbenutzung vom Stromnetz getrennt
werden.
Zum Schutz des Mikrophons bei Nahbesprechung
wird die Verwendung eines Popschutzes PS15
oder PS20 a empfohlen. Nähere Angaben dazu im
Kapitel „Zubehör“.
wird die Verwendung eines Popschutzes PS15
oder PS20 a empfohlen. Nähere Angaben dazu im
Kapitel „Zubehör“.
2.3 Ausführungsform und Beschaltung des
Mikrophon- und Netzgeräteausganges
Das Mikrophon kann in folgenden Ausführungsfor-
men geliefert werden:
men geliefert werden:
M 149 Tube (EU) ...... ni ........ Best.-Nr. 08390
M 149 Tube (US) ...... ni ........ Best.-Nr. 08399
M 149 Tube (UK) ..... ni ........ Best.-Nr. 08403
M 149 Tube (US) ...... ni ........ Best.-Nr. 08399
M 149 Tube (UK) ..... ni ........ Best.-Nr. 08403
Das Mikrophon hat eine nickelmatte Oberfläche.
Der 8-polige Stecker des Mikrophons und des
Netzgerätes ist folgendermaßen beschaltet:
Der 8-polige Stecker des Mikrophons und des
Netzgerätes ist folgendermaßen beschaltet:
Pin 1: –70 V
Pin 2: +5 V
Pin 3: Modulation (+Phase)
Pin 4: +70 V
Pin 5: Sensorleitung
Pin 6: Masse
Pin 7: +32 V
Pin 8: Modulation (–Phase)
Das zum Lieferumfang gehörende 8-polige Kabel
verbindet das Mikrophon mit dem Netzgerät.
verbindet das Mikrophon mit dem Netzgerät.
Within a few minutes, at the latest, the tube in the
M 149 Tube reaches its stable operating condition
and then evidences its particularly low residual
noise level.
M 149 Tube reaches its stable operating condition
and then evidences its particularly low residual
noise level.
When switching the directional characteristic, an
elevated noise floor can be noticed for 30 s max.
This is due to the reloading of the capsule to the
appropriate polarization voltage.
elevated noise floor can be noticed for 30 s max.
This is due to the reloading of the capsule to the
appropriate polarization voltage.
External phantom power, if present, does not de-
tract from the performance of the M 149 Tube. If an
external phantom power source is switched on or
off, only a short, slight rise in the residual noise
level will result.
tract from the performance of the M 149 Tube. If an
external phantom power source is switched on or
off, only a short, slight rise in the residual noise
level will result.
The on/off switch of the power supply functions as
a secondary voltage interrupt for the feeds from
the built-in mains unit. To save energy, the pow-
er supply should be unplugged from the wall out-
let if it goes unused for an extended period.
a secondary voltage interrupt for the feeds from
the built-in mains unit. To save energy, the pow-
er supply should be unplugged from the wall out-
let if it goes unused for an extended period.
To protect the microphone in close miking appli-
cations we recommend using a pop screen PS15
or PS20 a. For details, see the topic “Accesso-
ries”.
cations we recommend using a pop screen PS15
or PS20 a. For details, see the topic “Accesso-
ries”.
2.3 Type and Configuration of the Microphone and
Power Supply Outputs
The following versions of the M 149 Tube micro-
phone are available:
phone are available:
M 149 Tube (EU) ..... ni .......... Cat. No. 08390
M 149 Tube (US) ..... ni .......... Cat. No. 08399
M 149 Tube (UK) ..... ni .......... Cat. No. 08403
M 149 Tube (US) ..... ni .......... Cat. No. 08399
M 149 Tube (UK) ..... ni .......... Cat. No. 08403
The microphone is finished in matt nickel. The
8-pin connector of the microphone and the corre-
sponding connector of the power supply unit have
the following configuration:
8-pin connector of the microphone and the corre-
sponding connector of the power supply unit have
the following configuration:
Pin 1: –70 V
Pin 2: +5 V
Pin 3: audio signal (+phase)
Pin 4: +70 V
Pin 5: sensor line
Pin 6: ground
Pin 7: +32 V
Pin 8: audio signal (–phase)
The included eight-core cable connects the micro-
phone to the power supply unit.
phone to the power supply unit.
Die Modulation liegt hier an einem 3-poligen
XLR-Stecker. Erforderliches Gegenstück: XLR 3 F.
Die Zuordnung der Mikrophonanschlüsse ent-
spricht DIN EN 60268-12 bzw. IEC 60268-12:
XLR-Stecker. Erforderliches Gegenstück: XLR 3 F.
Die Zuordnung der Mikrophonanschlüsse ent-
spricht DIN EN 60268-12 bzw. IEC 60268-12:
Bei einem Schalldruckanstieg vor der vorderen
Mikrophonmembran tritt an Pin 2 eine positive
Spannung auf.
Mikrophonmembran tritt an Pin 2 eine positive
Spannung auf.
2.4Mikrophonkabel
Für das M 149 Tube stehen folgende Kabel zur Ver-
fügung:
fügung:
KT 8 (10 m) ....... sw ............ Best.-Nr. 08407
(gehört zum Lieferumfang)
(gehört zum Lieferumfang)
Kabel für M 147/M 149/M 150 Tube mit Doppel-
drallumspinnung als Abschirmung. Ø 5 mm, Länge
10 m. DIN 8-Steckverbinder.
drallumspinnung als Abschirmung. Ø 5 mm, Länge
10 m. DIN 8-Steckverbinder.
IC 3 mt ............... sw ............ Best.-Nr. 06543
Mikrophonkabel mit Doppeldrallumspinnung als
Abschirmung. Ø 5 mm, Länge 10 m. XLR 3 Steck-
verbinder, schwarzmatt.
Abschirmung. Ø 5 mm, Länge 10 m. XLR 3 Steck-
verbinder, schwarzmatt.
Andere Kabellängen sind auf Wunsch lieferbar.
Das Mikrophon ist besonders unempfindlich gegen
kapazitive Belastung. TIM- und Frequenzgangver-
zerrungen werden auch bei Verwendung sehr lan-
ger Kabel nicht hervorgerufen. Daher sind für die
Modulation Kabellängen bis etwa 300 m erlaubt.
Das 8-polige Kabel zwischen Mikrophon und Netz-
gerät darf dabei bis etwa 100 m lang sein.
kapazitive Belastung. TIM- und Frequenzgangver-
zerrungen werden auch bei Verwendung sehr lan-
ger Kabel nicht hervorgerufen. Daher sind für die
Modulation Kabellängen bis etwa 300 m erlaubt.
Das 8-polige Kabel zwischen Mikrophon und Netz-
gerät darf dabei bis etwa 100 m lang sein.
3.
Netzgerät
Das Universal-Netzgerät N 149 A kann in folgen-
den Ausführungsformen geliefert werden:
den Ausführungsformen geliefert werden:
N 149 A EU ......... sw ............ Best.-Nr. 08447
N 149 A US ......... sw ............ Best.-Nr. 08446
N 149 A UK ......... sw ............ Best.-Nr. 08448
N 149 A US ......... sw ............ Best.-Nr. 08446
N 149 A UK ......... sw ............ Best.-Nr. 08448
Die unterschiedlichen Versionen der Netzgeräte
unterscheiden sich lediglich durch ihre Netzkabel.
unterscheiden sich lediglich durch ihre Netzkabel.
Das Vintage-Netzgerät N 149 V kann in folgenden
Ausführungsformen geliefert werden:
Ausführungsformen geliefert werden:
N 149 V EU ............................ Best.-Nr. 08540
N 149 V US ............................ Best.-Nr. 08541
N 149 V UK ........................... Best.-Nr. 08542
N 149 V US ............................ Best.-Nr. 08541
N 149 V UK ........................... Best.-Nr. 08542
Die unterschiedlichen Versionen der Netzgeräte
unterscheiden sich lediglich durch ihre Netzkabel.
unterscheiden sich lediglich durch ihre Netzkabel.
At the power supply unit, the audio signal is avail-
able at a 3-pin XLR socket which requires an
XLR 3 F connector. The microphone is wired as per
DIN EN 60268-12 or IEC 60268-12:
able at a 3-pin XLR socket which requires an
XLR 3 F connector. The microphone is wired as per
DIN EN 60268-12 or IEC 60268-12:
An increase in sound pressure at the microphone‘s
front diaphragm produces a positive voltage at
pin 2.
front diaphragm produces a positive voltage at
pin 2.
2.4Microphone Cables
The following cables are available for the
M 149 Tube:
M 149 Tube:
KT 8 (10 m) ....... blk ............. Cat. No. 08407
(included in the supply schedule)
(included in the supply schedule)
Cable for M 147/149/150 Tube, with double twist
(double helix) braiding as shield. Ø 5 mm, length
10 m. DIN 8 connectors.
(double helix) braiding as shield. Ø 5 mm, length
10 m. DIN 8 connectors.
IC 3 mt ................ blk ............. Cat. No. 06543
Microphone cable with double twist (double helix)
braiding as shield. Ø 5 mm, length 10 m. XLR 3
connectors, matte black.
braiding as shield. Ø 5 mm, length 10 m. XLR 3
connectors, matte black.
Custom-made cables are available on request.
The microphone is especially insensitive to ca-
pacitive loads. Even the use of long cables does
not cause TIM or frequency response distortions.
Thus, the audio signal cable can have a length of
up to approx. 300 m, the 8-core connecting cable
between the microphone and the power supply
unit can be as long as approx. 100 m.
pacitive loads. Even the use of long cables does
not cause TIM or frequency response distortions.
Thus, the audio signal cable can have a length of
up to approx. 300 m, the 8-core connecting cable
between the microphone and the power supply
unit can be as long as approx. 100 m.
3.
Power Supply Unit
The N 149 A power supply unit is available in the
following versions:
following versions:
N 149 A EU .......... blk ............. Cat. No. 08447
N 149 A US .......... blk ............. Cat. No. 08446
N 149 A UK ......... blk ............. Cat. No. 08448
N 149 A US .......... blk ............. Cat. No. 08446
N 149 A UK ......... blk ............. Cat. No. 08448
The three available versions of the N 149 A just
differ in their enclosed mains power cable.
differ in their enclosed mains power cable.
The N 149 V vintage power supply unit is avail-
able in the following versions:
able in the following versions:
N 149 V EU .............................. Cat. No. 08540
N 149 V US .............................. Cat. No. 08541
N 149 V UK ............................. Cat. No. 08542
N 149 V US .............................. Cat. No. 08541
N 149 V UK ............................. Cat. No. 08542
The three available versions of the N 149 V just
differ in their enclosed mains power cable.
differ in their enclosed mains power cable.