Motorola MPC8260 User Manual

 

MOTOROLA

 

  

14-13

 

When MCC = 1, the SI

 

 

This example shows how to program the RAM to support the 10-bit IDL bus. Figure 14-23
shows the 10-bit IDL bus format. In this example, the TSA supports the B1 channel with
SCC2, the D channel with SCC1, the Þrst 4 bits of the B2 channel with an external device
(using a strobe to enable the external device), and the last 4 bits of B2 with SMC1.
Additionally, the TSA marks the D channel with another strobe signal. 

 

0

MCC

If MCC =1, the other SI

 

 RAM entries in this table are valid:

1

LOOP/
ECHO

Channel loopback or echo. 
0 Normal mode of operation.
1 Operation depends on the following conÞgurations:

In the receive SI

 

 RAM, this bit selects loopback mode for this MCC channel. The channelÕs 

transmit data is sent to both the receiverÕs input and to the data output line.
In the transmit SI

 

 RAM, this bit selects echo mode for this MCC channel. The channelÕs receive 

data is sent both to the transmitterÕs line and to the receiverÕs input.

To use the loop/echo modes, program the receive and transmit SI

 

 RAMs identically, except that 

the LOOP/ECHO bit should be set in only one of the entry pairs; that is, select only one of the 
modes (echo or loopback, not both) per MCC slot. Also, the receive and transmit clocks must be 
identical. 

2

SUPER MCC super channel enable. See Section 27.5, ÒSuper-Channel Table.Ó

0 The current entry refers to a regular channel.
1 The current entry refers to a super channel.

3Ð10

MCSEL MCC channel select. Indicates the MCC channel the bit/byte group is routed to. 0000_0000 selects 

channel 0; 1111_1111, selects channel 255.
For SI1 use values 0Ð127 and for SI2 use values 128Ð255. Note that the channel programming 
must be coherent with the MCCF; see Section 27.8, ÒMCC ConÞguration Registers (MCCFx).Ó

11Ð13

CNT

Count. 
If SUPER = 0 (normal mode), CNT indicates the number of bits/bytes (according to the BYT bit) 
that the routing select of this entry controls. 000 = 1 bit/byte; 111 = 8 bits/bytes.
If SUPER = 1 (MCC super channel), CNT and BYT together indicate whether the current entry is 
the Þrst byte of the MCC super channel.
CNT= 000 and BYT = 1ÑThe current entry is the Þrst byte of this MCC super channel.
CNT= 111 and BYT = 0ÑThe current entry is not the Þrst byte of this MCC super channel.
Note that because all SI

 

 RAM entries relating to super channels must be 1-byte in resolution, only 

the above two combinations of CNT and BYT are allowed when SUPER = 1.

14

BYT

Byte resolution
0 Bit resolution. The CNT value indicates the number of bits in this group.
1 Byte resolution. The CNT value indicates the number of bytes in this group.

15

LST

Last entry in the RAM. Whenever the SI

 

 RAM is used, LST must be set in one of the Tx or Rx 

entries of each group. Even if all entries of a group are used, LST must still be set in the last entry.
0 Not the last entry in this section of the route RAM.
1  Last entry in this RAM. After this entry, the SI waits for the sync signal to start the next frame.
Note that there must be only an even number of entries in an SI

 

 RAM frame, because LST is 

active only in odd-numbered entries (assuming the entry count starts with 0). Therefore, to obtain 
an even number of entries, an entry may need to be split into two entries.