JVC LVT1833-010B User Manual
Ba
sic ope
rat
io
ns
14
The K2 function is designed to provide natural
sound by improving the playback sound from low-
bit-rate digital sources.
The function compensates for sound waves dissi-
pated during digital recording compression to
approximate the original analog sound. Sound is
reproduced with more bits (24 bit) and a wider
range of frequency (64 kHz, 176.4 kHz or
192 kHz).
sound by improving the playback sound from low-
bit-rate digital sources.
The function compensates for sound waves dissi-
pated during digital recording compression to
approximate the original analog sound. Sound is
reproduced with more bits (24 bit) and a wider
range of frequency (64 kHz, 176.4 kHz or
192 kHz).
Press [K2] on the remote control or on
the main unit.
the main unit.
• When the K2 function is activated, the [K2] lamp
(button) on the main unit lights up.
• Each time you press [K2], the display changes
as follows.
- “K2 MODE1”:
- “K2 MODE1”:
Plays back a digital source with non-com-
pressed sound signals (linear PCM).
pressed sound signals (linear PCM).
- “K2 MODE2”:
Plays back a digital source with compressed
sound signals (Dolby digital, DTS, MP3, WMA
or WAV).
sound signals (Dolby digital, DTS, MP3, WMA
or WAV).
- “K2 OFF”:
Cancels the K2 function.
NOTE
• The original range of frequency is automatically
• The original range of frequency is automatically
detected and extended to a specific range.
You can adjust the volume level for the left and
right surround sound and the subwoofer sound
respectively.
right surround sound and the subwoofer sound
respectively.
1
Press [SPK LEVEL] repeatedly to
select “SURR” or “SUBWFR” in
the display window.
select “SURR” or “SUBWFR” in
the display window.
• “SURR” refers to the left and right surround
sound.
• “SUBWFR” refers to the subwoofer sound.
2
Press [LEVEL +] or [LEVEL –]
repeatedly to adjust the volume
level.
repeatedly to adjust the volume
level.
• The adjustable volume range is from -6 to +6.
Press [SURROUND].
• Each time you press [SURROUND], the display
changes in the display window as follows.
- “AUTO SUR”
- “AUTO SUR”
When a multi-channel signal is input, surround
sound is automatically produced.
sound is automatically produced.
- “MOVIE”
Surround sound suitable for a movie or multi-
channel signal is produced.
channel signal is produced.
- “WIDE/2CH”
When a 2ch signal is input, surround sound is
produced. The sound is broader than the one
with “MOVIE”.
produced. The sound is broader than the one
with “MOVIE”.
- “SUPER W”
Surround sound broader than the one with the
“WIDE/2CH” is produced.
“WIDE/2CH” is produced.
NOTE
• Depending on the signal type, surround sound
• Depending on the signal type, surround sound
may not be produced as the surround mode set-
ting.
ting.
• During playback, when you change the surround
mode setting, sound from the [DIGITAL OUT]
terminal may be intermittent. Before recording
sound to an external device, select the desired
surround mode setting.
terminal may be intermittent. Before recording
sound to an external device, select the desired
surround mode setting.
• This function does not work for a JPEG/ASF/
DivX/MPEG1/MPEG2 file.
Enhancing the playback
sound (K2) (Only for NX-F7)
sound (K2) (Only for NX-F7)
Adjusting the volume level
for surround/subwoofer
sound
for surround/subwoofer
sound
Selecting the surround mode
NX-F3_NX-F7[US]-04.fm Page 14 Tuesday, April 29, 2008 3:17 PM