Manualsbrain.com
  1. Manuals
  2. Brands
  3. PYLE Audio
  4. PICL82
  5. User Manual

PYLE Audio PICL82 User Manual

Download
Page of 6
LOCATION OF CONTROLS 
 
 
1. 
Speakers   
16. 
CD Door Open Button 
2. 
Power/Alarm Off Button 
17. 
CD Door 
3. Play/Pause/Sync 
Button 
18. Display 
4. 
Function/Clock Adj. Button 
19. 
Remote Sensor 
5. 
Skip-/Tune- Button 
20. 
Adjustable Dock Dial 
6. 
Skip+/Tune+ Button 
21. 
iPod/iPhone Connector 
7. 
Memory-/Alarm 1 Button 
22. 
FM Wire Antenna 
8. 
Memory+/Alarm 2 Button 
23. 
Aux-In Jack 
9. 
P-Mode Button 
24. 
DC In Jack 
10. 
Sleep Button 
25. 
Remote Control 
11. Snooze 
Button 
   
12. Stop 
Button 
   
13. Program/Mem 
Button 
   
14. Volume– 
Button 
   
15. Volume+ 
Button 
   
 
 
 
- 4 - 
CONNECTING THE UNIT TO POWER 
Plug one end of the AC/DC adaptor into the DC-In jack, and then plug the other end into AC wall outlet. 
Before switching on the unit, make sure that the voltage of your electricity supply is the same as that 
indicated on the rating plate. 
 
CONNECTING THE LOUDSPEAKERS 
Connect the cables of the two loudspeakers to the corresponding input (R) for the right speaker and 
input (L) for the left speaker, located at the side of the unit. 
Warning:  Connect the loudspeakers before powering the unit. The unit may not work properly or get 
damaged if you use speakers different than the ones supplied with the unit. 
 
SETTING THE TIME 
Before starting to set the time, make sure that the unit is in POWER OFF Mode. 
If you have iPod (Except iPod Shuffle) or iPhone 
1. 
Dock in the iPod/iPhone on the 30 pins Connector 
2. 
Press the ‘PLAY/PAUSE/SYNC’ button for a few seconds until the display will show SYNC with 
flashing, then the unit will synchronize the time same as the iPod/iPhone’s automatically. 
If you do not have any iPod/iPhone units 
1. 
Press and hold the ‘FUNC/CL ADJ’ button for a few seconds, the hour digit in the display will start 
flashing. 
2. 
Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button to adjust the hour.   
3. 
When the correct hour is selected, press the ‘FUNC/CL.ADJ’ button again, the minute digit in the 
display will start flashing. 
4. 
Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button to adjust the minute.   
5. 
When the correct time is selected, press the ‘FUNC/CL ADJ’ button to store the time in the memory. 
 
SETTING THE ALARM TIME 
Before starting to set the alarm time, make sure that the unit is in POWER OFF mode. 
1. 
Press the ‘MEM-/AL1’ or ‘MEM+/AL2’ button on the unit once (you can also use the ‘AL1’ or ‘AL2’ 
button on the remote control) and the AL1 or AL2 icon will appear in the display. 
2. 
Press the ‘FUNC/CL. ADJ.’ button to select the alarm wake up source. The options are buzzer, 
iPod/iPhone, Radio or CD.   
3. 
Press and hold the ‘MEM-/AL1’ or ‘MEM+/AL2’ button on the unit for a few seconds (you can also 
use the ‘AL1’ or ‘AL2’ button on the remote control), the alarm hour digit will begin flashing. 
4. 
Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button on the unit to adjust the alarm hour.   
5. 
When the desired alarm hour is selected, press the ‘MEM-/AL1’ or ‘MEM+/AL2’ button again, (you 
can also use the ‘AL1’ or ‘AL2’ button on the remote control), the alarm minute digit will begin 
flashing. 
6. 
Press the ‘SKIP+/TUNE+’ or ‘SKIP-/TUNE-‘ button on the unit to adjust the alarm minute. 
7. 
When the desired alarm time is selected, press the ‘MEM-/AL1’ or ‘MEM+/AL2’ button again to 
confirm. (You can also use the ‘AL1’ or ‘AL2’ button on the remote control). 
 
Note : If you choose iPod/iPhone or CD as the alarm wake up source, please make sure that you have 
the iPod/iPhone or CD in place. 
 
 
 
 
 
- 5 -