Sony HDCU-950 User Manual
1-12 (E)
HDCU-950 IMM
1-6-3. AVP-4 Board
n
Do not change the settings of the switches described
“Factory use only”.
Do not change the settings of the switches described
“Factory use only”.
. S1 (FP PGM SEL PGM1/MIX/PGM2)
Selects the PGM (program audio) that is output to the
INCOM connector on the front panel.
INCOM connector on the front panel.
PGM 1 : PGM CH-1
MIX :
MIX :
PGM CH-1
+ PGM CH-2
PGM 2 : PGM CH-2
Factory setting : PGM 1
. S2 (MIC 1 LEVEL)
. S3 (MIC 2 LEVEL)
. S3 (MIC 2 LEVEL)
Use these switches to select AMP GAIN of MIC CH-1/
CH-2 of the camera head using this unit. Set GAIN to
either 60 dB (NORMAL), 50 dB, 40 dB, 30 dB or 20 dB
(MIN) according to MIC sensitivity and audio conditions
during shooting.
Factory setting : [NORM] (60 dB)
CH-2 of the camera head using this unit. Set GAIN to
either 60 dB (NORMAL), 50 dB, 40 dB, 30 dB or 20 dB
(MIN) according to MIC sensitivity and audio conditions
during shooting.
Factory setting : [NORM] (60 dB)
A
B
C
D
E
F
G
H
J
K
1
2
4
3
5
S1
S16
S15
S11
S3
S2
AVP
POWER
MIC LEVEL
2WIRE CANCEL
PGM1
PGM2
PGM1
LEVEL
LEVEL
PGM2
LEVEL
LEVEL
SIDE
TONE
TONE
INTERCOM
MIX
MIC2
MIC1
MIN
MIN
PROD
NORM
NORM
ENG
S14
S12
S610
S611
S710
S711
S502
S503
S500
S501
S101
S100
S102
S103
AVP-4 board (A side/panel side)
. S11 (FP INCOM MODE SEP/MIX/OFF)
Selects the receiving audio of the producer line (or
engineer line) and also selects the mix mode of the PGM
(program audio).
engineer line) and also selects the mix mode of the PGM
(program audio).
SEP : The receiving audio and the PGM (program
audio) are output in the right and left channels
separately.
separately.
MIX : The receiving audio and the PGM (program
audio) are mixed and output.
OFF : Not mixed. (Depends on the setting of S3 on the
AU-281 board.)
n
There is not the mix mode of the producer line and the
engineer line.
There is not the mix mode of the producer line and the
engineer line.
Factory setting : OFF
. S12 (INPUT INCOM SELECT)
Set this switch to either channel 1 (PROD) or channel 2
(PROD, ENG) according to the intercom system. When
channel 1 is set, PROD is selected regardless of the
setting of the ENG/PROD select switches of the camera
side and the CCU side.
Factory setting : Channel 2
(PROD, ENG) according to the intercom system. When
channel 1 is set, PROD is selected regardless of the
setting of the ENG/PROD select switches of the camera
side and the CCU side.
Factory setting : Channel 2
. S14 (PGM INPUT SEL ANA/SDI)
Selects the type of the PGM (program audio).
ANA : Analog system PGM (Input signals to the
INCOM/TALLY/PGM connectors)
SDI : Embedded digital audio of the SDI signal
selected by S605 on the DTX-1 board.
Factory setting : ANA
1-6. Setting of Switches on Boards