Sony HDCU-950 User Manual
2-21 (E)
HDCU-950 IMM
2-5-6. Adjusting the Level of Signals for
Picture Monitor
The video output signal can be checked on the waveform
or vector monitor connected to the PIX OUT connector.
Use the color bars to adjust the level of the PIX output
signal.
In addition, in the system with the MSU-700A/750, CNU-
700/500 or VCS-700, the video signal of the unit can be
checked on the waveform or vector monitor connected to
the VCS-700.
or vector monitor connected to the PIX OUT connector.
Use the color bars to adjust the level of the PIX output
signal.
In addition, in the system with the MSU-700A/750, CNU-
700/500 or VCS-700, the video signal of the unit can be
checked on the waveform or vector monitor connected to
the VCS-700.
How to adjust on the RC-91 board of the unit
RC-91 board (A side)
1.
Press the BARS button of the MSU-700A/750, RCP-
740/741, etc., and press the ENC button of the PIC-
TURE MONITOR buttons (or MONITOR SELECT
buttons) to display the color bars on the waveform
monitor.
740/741, etc., and press the ENC button of the PIC-
TURE MONITOR buttons (or MONITOR SELECT
buttons) to display the color bars on the waveform
monitor.
2.
Adjust the color bar signal using control RV302 (PIX
GAIN) on the RC-91 board so that it is within the
specified level.
Measurement point : PIX OUT connector on the
GAIN) on the RC-91 board so that it is within the
specified level.
Measurement point : PIX OUT connector on the
HDCU rear panel
Specification :
A = 100
±1 IRE [for NTSC]
A = 700
±7 mV p-p [for PAL]
How to adjust using the VCS-700
In the system with the MSU-700A/750, CNU-700/500 or
VCS-700, the video output signal of the unit can be
checked on the waveform or vector monitor connected to
the PIX A OUTPUT and PIX B OUTPUT connectors of
the VCS-700.
Connect the PIX OUT connector of the DIF-124 board to
the PIX 1 connector of the VCS-700 using the color bars
signal.
In the system with the MSU-700A/750, CNU-700/500 or
VCS-700, the video output signal of the unit can be
checked on the waveform or vector monitor connected to
the PIX A OUTPUT and PIX B OUTPUT connectors of
the VCS-700.
Connect the PIX OUT connector of the DIF-124 board to
the PIX 1 connector of the VCS-700 using the color bars
signal.
1.
Press the BARS button of the MSU-700A/750, RCP-
740/741, etc., or press the ENC button of the WAVE-
FORM MONITOR buttons (or MONITOR SELECT
buttons) to display the color bars on the waveform or
vector monitor.
740/741, etc., or press the ENC button of the WAVE-
FORM MONITOR buttons (or MONITOR SELECT
buttons) to display the color bars on the waveform or
vector monitor.
2.
Adjust the color bars signal using the PIX 1 LEVEL
and PIX 1 CHROMA controls on the VCR-700 board
so that it is within the specified level.
Measurement point : PIX OUT connector on the VCS-
and PIX 1 CHROMA controls on the VCR-700 board
so that it is within the specified level.
Measurement point : PIX OUT connector on the VCS-
700
Specification :
A = 100
±1 IRE [for NTSC]
A = 700
±7 mV p-p [for PAL]
(PIX 1 LEVEL control)
Each luminescent spot on the vector monitor must be
within the “
within the “
4” range.
(PIX 1 CHROMA control)
2-5. Video Signal System
[for PAL]
[for NTSC]
A
A
[for PAL]
[for NTSC]
A
A
R
M
G
B
C
Y
G
Y
L
R
M
G
C
Y
G
Y
L
B
[for NTSC]
[for PAL]
1
RV302
D
AB
C
1
2
3
4
5