Panasonic Crystal Eyes Wear Leaflet

2171 East Francisco Blvd., San Rafael, CA  94901

phone

800-783-2660  (within USA & Canada )

415-459-4500  (all other areas)

fax

415-459-3020

e-mail

Sales@StereoGraphics.com

web site www.StereoGraphics.com

StereoGraphics CrystalEyes

CrystalEyes requires the use of an infrared emitter in order to synchronize the eyewear in

conjunction with the left and right image sequence on screen.  The I/R receiver (located in the center of the
eyewear) must be in line of sight and in range of the emitter for successful operation of CrystalEyes.  Please
consult the documentation accompanying your emitter for installation and operation details.

In  all  cases  except  for  non-stereo-ready  PCs,  the  system  or  graphics  card  manufacturer  requires  specific  display
settings  to  enable  Stereo3D  mode.    Please  consult  the  manual  or  vendor  for  your  specific  graphics  subsystem  to
determine  the  proper  settings  for  Stereo3D  mode.    For  best  results  in  using  CrystalEyes

CrystalEyes  with  standard

workstation  displays,  set  the  emitter  slightly  behind  the  top  edge  of  the  monitor,  as  shown  in  Figure  1.    In
addition:

Installation & Setup

Each pair of Cr

ystalEyes eyewear includes two fresh batteries, which are installed at the factory. A compatible

stereo computer grapics or video system must be available to check the operation of the eyewear.  To activate
the eyewear, unfold the temple pieces; to turn off the eyewear, fold the templepieces.  When not in use, fold
your CrystalEyes

CrystalEyes eyewear with the temples laying flat across the back of the lenses for convenient storage.

• For EPRO, ESGI and ELR emitters, make sure the emitter is switched

to the ON position.  Depending on the emitter range needed, switch
the emitter to either the high or low setting.

• The ENT emitter will switch on and off automatically whenever a sync

signal is presented by the graphics card.

• Users of the EPC-2 must switch the emitter from BYPASS to STEREO

MODE and set the emitter range separately.

Figure 1. Display and Emitter

If you normally wear prescription eyeglasses, place CrystalEyes

CrystalEyes over them.  The eyewear will fit

comfortably over most prescription eyeglass frames.

For more information on setting up your system, please refer to our website at http://www.stereographics.com

Two 3 V lithium/manganese dioxide
(NEDA 5004L), including:

Eveready

E-CR2032

Maxell

CR2032

Panasonic

CR2032

Ray-O-Vac

CR2032

Saft

LM2032

Shutters:

liquid  crystal

Transmittance:

32%  typical

Dynamic  Range:

1000:1  typical

Close Time:

Less than 0.2 milliseconds

Open Time:

Less than 3 milliseconds

Field  Rate:

80 to 160 fields per second

Bright  Mode:

Automatically  selected

Infrared Sensor
   Angle of View:

90 degrees horizontal

140 degrees vertical

3.3 oz. (93 grams)

   Eyewear operation is switched on and off

by unfolding and folding the eyewear temple pieces.

:  Both lenses automatically switch to

full transparency for up to 8 minutes when shielded
from infrared signals.  Restoring the infrared signal
returns the eyewear to full operation.

Sanyo

CR2032

Seiko

CR2032

Technacell

CR2032

Varta

CR2032

Duracell

DL2032

Specifications