Viking viking User Manual
3
Illustration #3
Illustration #4
Install 4 Tinnerman clips (provided)
before fastening cabinets together
before fastening cabinets together
Mount cabinets
with #10 x 1/2”
screws provided
with #10 x 1/2”
screws provided
Use #8 x 3/8” machine screw and
locknut to fasten hole cover to
inside door panel
locknut to fasten hole cover to
inside door panel
Use #8 x 3/8” flat
head M.S. and
locknut to attach
hinge bracket to
the inside door.
head M.S. and
locknut to attach
hinge bracket to
the inside door.
7. Cabinet doors must be adjusted when cabinets are
level in final position. There are two adjustment
screws on the hinge receiver. (See Illustration #5)
screws on the hinge receiver. (See Illustration #5)
•The front screw is used to center the door in
the opening. Turning the front screws in or
out will center the door over the cabinet
opening.
out will center the door over the cabinet
opening.
•The back screw is used to align the front of
the door with the cabinet frame and secure
the door to the cabinet. Slightly loosen the
screw and slide door in or out. Retighten the
screw to secure the door.
the door to the cabinet. Slightly loosen the
screw and slide door in or out. Retighten the
screw to secure the door.
Illustration #5
Front Screw
5. Place cabinet(s) in approximate final position.
Level cabinets using leveling legs. Use 1/2"
SMS screws provided to screw cabinets
together. (See illustration #3).
SMS screws provided to screw cabinets
together. (See illustration #3).
6. Determine appropriate hinge side for cabinets
with interchangeable doors. Remove outside
door panel. Install hinges by placing plate in
hole in door and fasten in place with hardware
provided. Screw hinge plates in appropriate
pre-drilled holes in cabinet side. Fasten hole
covers with hardware provided. (See
Illustration #4).
door panel. Install hinges by placing plate in
hole in door and fasten in place with hardware
provided. Screw hinge plates in appropriate
pre-drilled holes in cabinet side. Fasten hole
covers with hardware provided. (See
Illustration #4).
Back Screw
2
IMPORTANT - PLEASE READ AND FOLLOW
•Before beginning, please read these instructions completely and carefully.
•Do not remove permanently affixed labels, warnings, or plates from product. This may void the warranty.
•Viking outdoor stainless steel cabinets are not designed to be water tight. Water may enter cabinetry under certain
•Do not remove permanently affixed labels, warnings, or plates from product. This may void the warranty.
•Viking outdoor stainless steel cabinets are not designed to be water tight. Water may enter cabinetry under certain
conditions
•The installer should leave instructions with the consumer who should retain for future reference
•NEVER use LP tanks inside any stainless steel cabinetry. Tanks must be located outside of the cabinetry at all times.
•NEVER use LP tanks inside any stainless steel cabinetry. Tanks must be located outside of the cabinetry at all times.
TO INSTALL CABINETS:
1. Verify cabinet product number(s) on
box(es) to list of cabinets ordered.
2. Carefully unpack cabinets making sure
not to scratch fronts. Front panels are
protected by plastic coating (that must
be removed after setup). Cabinets with
interchangeable doors are shipped from
the factory with opening from left to
right as shown (See illustration #1).
protected by plastic coating (that must
be removed after setup). Cabinets with
interchangeable doors are shipped from
the factory with opening from left to
right as shown (See illustration #1).
3. In cabinets with interchangeable doors,
hardware package will contain hole
covers and hardware to install.
covers and hardware to install.
4. Install 4 legs in the leg plates attached to
bottom of each cabinet. Screw in place.
(See illustration #2).
(See illustration #2).
Illustration #1
Illustration #2
Cabinet box ready
for assembly
for assembly