Suunto HELO2 User Manual
2.
Ensure that the Suunto HelO
2
is turned on, and that the wireless integration is enabled
in the Suunto HelO
2
settings (HP set ON, see Section 5.9.8. Setting the HP code).
The HelO
2
should display “cd:--” in the lower left corner of the alternative display.
3.
Slowly open the cylinder valve fully and pressurize the regulator. The transmitter starts
transmitting when the pressure exceeds 15 bar/218 psi.
transmitting when the pressure exceeds 15 bar/218 psi.
4.
Take the Suunto HelO
2
wrist unit close to the transmitter. The unit will then quickly
display the selected code number and then start displaying the transmitted cylinder
pressure. The wireless transmitter indicator is displayed every time the Suunto receives
a valid signal.
pressure. The wireless transmitter indicator is displayed every time the Suunto receives
a valid signal.
WARNING
If there are several divers using Suunto HelO
2
with wireless transmis-
sion, always ensure that each diver is using a different code before
starting the dive.
You can manually change the transmitter’s code by reducing the
pressure to less than 10 bar/145 psi and then immediately (within 10-
12 seconds) increasing the pressure to above 15 bar/220 psi.
Reset the transmitter's code manually, see Section 5.9.8. Setting the
HP code.
The transmitter will then select a new code. The Suunto HelO
starting the dive.
You can manually change the transmitter’s code by reducing the
pressure to less than 10 bar/145 psi and then immediately (within 10-
12 seconds) increasing the pressure to above 15 bar/220 psi.
Reset the transmitter's code manually, see Section 5.9.8. Setting the
HP code.
The transmitter will then select a new code. The Suunto HelO
2
must
be in “cd:--“ mode to pair on the new code. This procedure can be
used if, for example, your dive buddy has the same code and you
need to change it.
used if, for example, your dive buddy has the same code and you
need to change it.
NOTE
In order to save battery energy, the transmitter shuts off if the pressure
remains unchanged for more than 10 minutes, and it will continue
transmitting with the saved code when any pressure change is
measured.
remains unchanged for more than 10 minutes, and it will continue
transmitting with the saved code when any pressure change is
measured.
5.8.3. Transmitting data
After the pairing procedure, the Suunto HelO
After the pairing procedure, the Suunto HelO
2
will receive cylinder pressure data from the
transmitter. The pressure is displayed in either bars or psi, depending on the unit selected.
Any time the Suunto HelO
Any time the Suunto HelO
2
receives an appropriate signal it flashes the wireless transmitter
indicator in the display’s lower left corner.
Table 5.3. Pressure transmission related displays
Figure
Indication
Display
A
Set Code. No code stored, Suunto HelO
2
ready for pairing with trans-
mitter.
Cd:--
B
Pressure reading over 360 bar/5220 psi.
- - -
C
Pressure reading has not been updated for more than one minute.
The latest valid pressure reading is displayed intermittently. After five
minutes, "FAIL" is displayed intermittently with "---".
Transmitter is out of range, in power saving mode or on another
channel. Activate the transmitter by breathing off the regulator, and
recode the wrist unit if necessary.
The latest valid pressure reading is displayed intermittently. After five
minutes, "FAIL" is displayed intermittently with "---".
Transmitter is out of range, in power saving mode or on another
channel. Activate the transmitter by breathing off the regulator, and
recode the wrist unit if necessary.
FAIL
D
Pressure transmitter battery voltage is low. The pressure reading is
displayed intermittently. Change the transmitter battery!
displayed intermittently. Change the transmitter battery!
LOb
E
Pairing has not been conducted between the dive computer and the
transmitter before start of dive. No cylinder data available.
transmitter before start of dive. No cylinder data available.
OFF
18