Sony PCS-1P User Manual
2-17
PCS-1/1P
For loading of application
1.
Display a service menu.
2.
Insert the Memory Stick, in which the application
software of the version to be loaded is recorded, into a
software of the version to be loaded is recorded, into a
Memory Stick slot.
3.
Select “Load application” using
↑
,
↓
,
←
, and
→
buttons of a remote controller and press the ENTER
button.
button.
4.
A confirmation message on whether to execute is
displayed.
displayed.
5.
To execute, select “OK” and press the ENTER button.
The screen display during loader execution then
The screen display during loader execution then
appears. After completion, a launcher menu is
displayed. To cancel execution, select “Cancel” and
displayed. To cancel execution, select “Cancel” and
press the ENTER button. The current display returns
to a service menu.
to a service menu.
6.
Push in the Memory Stick once and take out it.
n
Do not turn off the power or take out a Memory Stick until
Do not turn off the power or take out a Memory Stick until
the launcher menu is displayed.
For command input
1.
Display a service menu.
2.
Select “Command” using
↑
,
↓
,
←
, and
→
buttons of a
remote controller and press the ENTER button.
A key guidance is then displayed.
3.
Enter the commands in a command list from a remote
controller.
m
. To set two or more commands, put a one-character
m
. To set two or more commands, put a one-character
blank between the commands and then enter them.
. Set only one type of LAN interface. If not, the LAN
interface does not operate normally.
4.
Select “Save” using
↑
,
↓
,
←
, and
→
buttons of a
remote controller and press the ENTER button.
A set menu is then displayed.
5.
When a LAN interface is set (including the case where
the setting is returned to the initial value), restart the
main unit using the power switch of a communication
main unit using the power switch of a communication
terminal.
To stop setting
Select “Cancel” using
↑
,
↓
,
←
, and
→
buttons of a remote
controller and press the ENTER button, or press the return
button of a remote controller.
n
Do not enter commands other than shown in a command
button of a remote controller.
n
Do not enter commands other than shown in a command
list. The internal operation mode may be changed in this
case.
case.
Contents of functions
1) Command
The internal operation mode of the main unit is
changed for a test and service.
Command list
m
. To set two or more types of commands, put a one-
. To set two or more types of commands, put a one-
character blank between commands.
. The validated command can be confirmed in a command
column at all times.
. Do not enter commands other than described in the table.
This may change the internal operation mode.
Command
SMS
KV66
WBxxxXyyy
YCLP**
YLVL**
D2B
PWD1
SMFF
BMR0
SMSTEST
PROJ
POFF
Description
Validates an SMS function.
Sets a KV-29FX66E monitor when it is used.
Using an IR repeater, this command sets the
input selection of a KV-29FX66E monitor to 3
after the power is turned on.
An IR output is changed so that the
command during power-off sequence is sent
properly. The setting of the IR repeater
mode is invalided when this command is
specified.
Using an IR repeater, this command sets the
input selection of a KV-29FX66E monitor to 3
after the power is turned on.
An IR output is changed so that the
command during power-off sequence is sent
properly. The setting of the IR repeater
mode is invalided when this command is
specified.
Sets the size (height
x
width) of the
whiteboard used.
Clips the luminance value in a menu to the
specified value.
The section having the luminance of more
than the specified value is clipped to the
specified value. (** is one of 80, 90, A0, B0,
C0, D0, and E0 values.)
specified value.
The section having the luminance of more
than the specified value is clipped to the
specified value. (** is one of 80, 90, A0, B0,
C0, D0, and E0 values.)
Shifts the luminance value in a menu
downward proportionally to the specified
value.
As a value increase, the whole screen
becomes darker.
Since all values are shifted, the black side
seems crushed.
(** is a value of 0 < ** < 80 in decimal.)
downward proportionally to the specified
value.
As a value increase, the whole screen
becomes darker.
Since all values are shifted, the black side
seems crushed.
(** is a value of 0 < ** < 80 in decimal.)
Sets ISDN (2B) to the default value using a
dial menu. Usually, set to LAN.
dial menu. Usually, set to LAN.
The password for an administrator invalidates
the password lock of a phone book when a
setting super-user password is blank in a
column.
the password lock of a phone book when a
setting super-user password is blank in a
column.
Fixes a sub-monitor to the remote video.
Sets the bonding mode to Revision 0 (in
which up to the conventional seven-digit
address number can be used).
which up to the conventional seven-digit
address number can be used).
Displays SAB without connecting with the
SMS server.
SMS server.
Sends the remote control code for the projector.
Makes the packet loss indicator non-display.