Electrolux 9CHG584159 User Manual
INSTALLATION INSTRUCTIONS
Page 6
62.9534.01_UL
1.4
SIDEWALL (D)
The assembly kit contains two of each of the following:
hexagonal screws M8x25 (1 / Fig.1), bolts with retaining rings
(2 / Fig.1), mounting links (3 / Fig.1), hexagonal screws M8x16
with serrated washers and hexagonal nuts M8, hexagonal
screws M5 with serrated washers (4 / Fig.2)
and a fastening angle (5 / Fig.2).
hexagonal screws M8x25 (1 / Fig.1), bolts with retaining rings
(2 / Fig.1), mounting links (3 / Fig.1), hexagonal screws M8x16
with serrated washers and hexagonal nuts M8, hexagonal
screws M5 with serrated washers (4 / Fig.2)
and a fastening angle (5 / Fig.2).
D
Insert the bolts with the retaining rings (2 / Fig.1a) from out-
side into the guide in the sidewall.
side into the guide in the sidewall.
D
Keeping the screw (1 / Fig.1a) loose, turn it until it is
approximately 5 mm deep in the pre-assembled caged
nuts in the sidewall.
approximately 5 mm deep in the pre-assembled caged
nuts in the sidewall.
D
Attach the fastening angle (5 / Fig.2b) to the bottom of the
frame using the screws, serrated washers and nuts.
frame using the screws, serrated washers and nuts.
D
(4 / Fig.2).
D
Position the sidewall and screw it on from below using two
hexagonal screws and the serrated washers.
hexagonal screws and the serrated washers.
D
Fit the mounting link (3 / Fig.1b) into the inside of the appli-
ance's connecting plate.
ance's connecting plate.
D
Align the sidewall and firmly tighten all screws.
1.5
STEEL PLINTH
To assemble the plinth you will need:
•
•
Right and left side plinth (1 / Fig.3).
•
Plinth for the front and, for free-standing appliances, for the
rear also (2 / Fig.3).
rear also (2 / Fig.3).
D
Push the side plinth (1 / Fig.3) onto the legs from front to
rear using the fastener. The larger gap (b / Fig.3) on the
fastener must be at the bottom.
rear using the fastener. The larger gap (b / Fig.3) on the
fastener must be at the bottom.
D
Affix the fasteners (3 / Fig.3) to the plinth (2 / Fig.3).
D
The larger gap (b / Fig.3) on the fastener must be at the
bottom.
bottom.
D
Attach the plinth with the fasteners (3 / Fig.3) onto the feet.
1.6
ASSEMBLING ON CASTORS
The assembly kit for mounting on castors contains two cross
bars (2/Fig.4a) each with a fixed rear wheel (1/Fig.4a) and a
turnable front wheel (3/Fig.4a).
Mounting the castors:
bars (2/Fig.4a) each with a fixed rear wheel (1/Fig.4a) and a
turnable front wheel (3/Fig.4a).
Mounting the castors:
D
Put the appliance on supports.
D
Remove the feet; each is tightened with four screws
(Fig.4b).
(Fig.4b).
D
Bring the two cross bars into the correct position below the
appliance and fasten it with 8 screws arrows (Fig.4a).
appliance and fasten it with 8 screws arrows (Fig.4a).
D
Remove the supports.
D
Fasten the appliance to the building. Use the hole to attach
a chain descending from the wall (arrow/Fig.4c). Making
sure the chain is shorter than the gas and electric connec-
tions.
a chain descending from the wall (arrow/Fig.4c). Making
sure the chain is shorter than the gas and electric connec-
tions.
Note:
Appliances on wheels must be secured by fasten it to the
building.
Appliances on wheels must be secured by fasten it to the
building.
2.
ACCESS TO INTERIOR
Note:
Only authorized technicians may access the interior.
Only authorized technicians may access the interior.
a
b
Fig.2
Assemblage of sidewall
a
b
Fig. 3 Plinth assembly
1
()
(5)
(4)
1
(3c)
1
()
(5)
(4)
(1)
(2)
(3)
b
b
1
(3c)
(1)
(2)
(3)
a
b
c
Fig.4
Assemblage on castors
Fig. 5 General view
1
()
(5)
(4)
1
(3c)
1
(3c)
1
3
1
3
D
D
B
E
C
1 1