Liebherr 220113 7082814 - 00 User Manual

The  layer  of  frost  or  ice  builds  up  faster  if  the  appliance  is

opened  often  or  if  the  food  is  warm  when  placed  inside.

However,  a  thick  layer  of  ice  will  increase  the  appliance‘s

energy  consumption.  You  should  therefore  defrost  the  appli-

ance regularly.

Risk of injury and damage as a result of hot steam!

u

Do not use electric heaters or steam cleaners, naked flames

or defrosting sprays for defrosting.

u

Do not remove ice using sharp instruments.

u

Switch off the appliance.

u

Pull out the power plug or switch off the fuse.

u

If  possible,  put  the  frozen  goods  in  the  freezer  drawer,

wrapped  in  newspaper  or  a  blanket,  and  store  in  a  cool

place.

u

Place  a  pan  with  hot,  not  boiling

water on a middle shelf.

u

Half-fill  the  two  lower  drawers  with

lukewarm water and put them in the

appliance.

w

Defrosting is speeded up.

w

Defrost water is collected in the drawers.

u

Leave the door of the appliance open while defrosting.

u

Remove detached pieces of ice.

u

If  necessary,  pick  up  defrost  water  several  times,  using  a

sponge or cloth.

u

Risk of injury and damage as a result of hot steam!

Hot steam may damage the surfaces and cause burns.

u

Do not use any steam cleaners!

Incorrect cleaning damages the appliance!

u

Do not use cleaning agents in concentrated form.

u

Do not use any scouring or abrasive sponges or steel wool.

u

Please  do  not  use  any  aggressive,  scouring,  sand-,

chloride-, chemical- or acid-based cleaning agents.

u

Do not use chemical solvents.

u

Do not damage or remove the type plate on the inside of the

appliance. It is important for the customer service.

u

Do  not  pull  off,  bend  or  damage  cables  or  other  compo-

nents.

u

Do not allow any cleaning water to enter the drain channel,

ventilation grille or electrical parts.

u

Please  use  soft  cleaning  cloths  and  a  universal  pH-neutral

cleaning agent.

u

Please use cleaning and care products suitable for contact

with foodstuffs in the appliance interior.

u

u

u

Clean the vent grille regularly.

w

Dust deposits increase energy consumption.

u

Clean  plastic  outer  and  inner  surfaces  with  lukewarm

water and a little washing-up liquid.

The  stainless  steel  doors  are  finished  with  a  high  quality

surface coating and must not be treated with the enclosed care

product,

as otherwise the surface coating will be damaged.

u

Please only use a soft clean cloth to wipe the coated door

surfaces. In the case of heavy soiling, use a little water or

neutral  cleaning  agent.  A  micro-fibre  cloth  can  be  used

optionally.

u

When  soiled,  clean  stainless  steel  side  walls  with  a

commercially available stainless steel cleaning agent. Then

apply the enclosed stainless steel care product evenly in the

direction of polishing.

u

Use  only  a  soft  clean  cloth  to  wipe  side  walls  and  door

surfaces with a paint finish. In the case of heavy soiling, use

a  little  water  or  neutral  cleaning  agent.  A  micro-fibre  cloth

can be used optionally.

u

Clean  drain  hole:  Remove

deposits  with  a  narrow  instru-

ment, e.g. a cotton bud.

u

Most  of  the  parts  can  be  dismantled  for  cleaning:  see  the

relevant chapter.

u

Clean  items  of  equipment  by  hand  with  lukewarm  water

and a little washing-up liquid.

u

Wipe dry the appliance and items of equipment.

u

Connect the appliance and switch it on again.

When the temperature is sufficiently cold:

u

Put the food back inside.

In the device, an LED lamp is used as standard illumination for

the interior space.
When an incandescent bulb is used:

q

Use an incandescent lamp with max. 15 W and E14 socket.

q

Power supply (AC) and voltage at the operating point must

comply with the details on the rating plate (see Appliance at

a glance).

q

Use only the original LED lamp from the manufacturer. The

lamp  can  be  obtained  through  customer  service  or  a

Risk of injury from LED light!

The  light  intensity  of  the  LED  lighting  corresponds  to  laser

class 1/1M.

If the cover is removed:

u

Do  not  look  directly  into  the  light  at  close  quarters  through

optical lenses. Doing so may damage your eyes.

Fire hazard from the LED light!

If different LED lights are used, there is a danger of overheating

or fire.

u

Use the manufacturer's original LED light.