Bosch SHU 9950 User Manual
ENGLISH - 23
www.boschappliances.com
Accomodating
Extra Tall Items
If you have extra tall items that cannot fit in the
bottom rack without interfering with the upper spray
arm or without hitting the top rack (max. height
22”), you can remove the upper rack. A special
accessory, the Extra Tall Item Sprinkler, lets you run
the dishwasher with top rack removed. See Figures
36 and 36.
bottom rack without interfering with the upper spray
arm or without hitting the top rack (max. height
22”), you can remove the upper rack. A special
accessory, the Extra Tall Item Sprinkler, lets you run
the dishwasher with top rack removed. See Figures
36 and 36.
Installing “Extra Tall
Item Sprinkler”
1. With top rack empty, remove it from the dish-
washer by pulling the rack toward you to the
point where you can lift it up and out, dis-
engaging the wheels from the side rails.
point where you can lift it up and out, dis-
engaging the wheels from the side rails.
2. Place the “Extra Tall Item Sprinkler” over the
top rack spray outlet at the back of the dish-
washer tub and turn it clockwise to lock the
sprinkler head in place. See Figure 37.
washer tub and turn it clockwise to lock the
sprinkler head in place. See Figure 37.
3. Place the extra tall items in the bottom rack
for washing, as shown in Figure 36. To
remove the Extra Tall Item Sprinkler, turn it
counterclockwise and pull it out. Then replace
the top rack.
remove the Extra Tall Item Sprinkler, turn it
counterclockwise and pull it out. Then replace
the top rack.
SPECIAL FEATURES
Figure 36
Figure 37
Note: Be sure to
remove the
Extra Tall Item Sprinkler before
you reinstall the top rack, oth-
erwise the door could become
damaged and not close properly.
L
E
D
O
M
N
O
T
T
U
B
m
a
r
g
o
r
P
0
5
9
9
U
H
S
s
r
u
o
H
t
r
a
t
S
y
a
l
e
D
0
2
9
9
/
0
1
9
9
U
H
S
o
n
o
c
E
/
e
t
a
c
il
e
D
0
1
8
8
/
0
0
8
8
U
H
S
h
s
a
W
k
c
i
u
Q
0
0
8
6
V
H
S
s
r
u
o
H
t
r
a
t
S
y
a
l
e
D
0
0
8
4
V
H
S
o
n
o
c
E
/
e
t
a
c
il
e
D
0
0
3
4
V
H
S
o
n
o
c
E
/
e
t
a
c
il
e
D
How to Operate the Cycle
Completion Signal
1. Open door, hold down program button (see
Beeper Table on right) and simultaneously turn the
Dishwasher on.
2. Release program button.
Beeper Table on right) and simultaneously turn the
Dishwasher on.
2. Release program button.
a. For SHV 6803 and SHU9950 models:
The display will blink with a code of “0”, “1” or
“2”. You are in program mode.
• If the display blinks with a “0”, you will hear
The display will blink with a code of “0”, “1” or
“2”. You are in program mode.
• If the display blinks with a “0”, you will hear
no signal (indicates OFF).
• If the display blinks with a “1”, you will hear a
LOW volume signal.
• If the display blinks with a “2”, you will hear a
HIGHER volume signal.
b. For all other models with the beeper
function:
• If the machine beeps, then the Cycle
Completion Signal has been enabled.
• When you push the button again and it does
not beep, it means that the Cycle Comple-
tion Signal has been disabled.
tion Signal has been disabled.
3. To change the program, press the program
button until the desired setting is selected.
4. Turn the Dishwasher off to take it out of
program mode.
* At the end of a wash cycle, the beeper will sound
off two times, and again every 15 minutes until the
dishwasher is turned off.
button until the desired setting is selected.
4. Turn the Dishwasher off to take it out of
program mode.
* At the end of a wash cycle, the beeper will sound
off two times, and again every 15 minutes until the
dishwasher is turned off.