Beko BZ30 User Manual
2
CONTENTS PAGE
SAFETY FIRST / ELECTRICAL REQUIREMENTS
TRANSPORTATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
REPOSITIONING THE DOOR
STARTING
TEMPERATURE CONTROL AND ADJUSTMENT
STORING FROZEN FOOD
FREEZING FRESH FOOD
DEFROSTING
CLEANING AND CARE
DO'S AND DON'TS
PROBLEM SOLVING
INSTALLATION INSTRUCTIONS - DETAILED STEP BY STEP
GUARANTEE DETAILS
HOW TO OBTAIN SERVICE
3
4
5
6-7
8
9
10
12
13
9
11
13
14-19
20
21
ELECTRICAL REQUIREMENTS
Before you insert the plug into the wall socket make sure that the voltage and the
frequency shown in the rating plate inside the appliance corresponds to your
electricity supply. Rating label is on the left hand side of freezer inner liner.
We recommend that this appliance is connected to the mains supply via a suitable
frequency shown in the rating plate inside the appliance corresponds to your
electricity supply. Rating label is on the left hand side of freezer inner liner.
We recommend that this appliance is connected to the mains supply via a suitable
switched and fused socket in a readily accessible position.
Should the mains lead of the appliance become damaged or should it need replacing
at any time, it must be replaced by a special purpose made mains lead which can
Should the mains lead of the appliance become damaged or should it need replacing
at any time, it must be replaced by a special purpose made mains lead which can
only be obtained from a BEKO Authorised Service Agent.
WARNING! THIS APPLIANCE MUST BE EARTHED
If the fitted moulded plug is not suitable for your socket, then the plug should be
If the fitted moulded plug is not suitable for your socket, then the plug should be
cut off and an appropriate plug fitted. Destroy the old plug which is cut off as a
plug with bared cord could cause a shock hazard if inserted into a socket elsewhere
in the house.
The moulded plug on this appliance incorporates a 13 A fuse. Should the fuse need
to be replaced an ASTABEAB approved BS 1362 fuse of the same rating must be
plug with bared cord could cause a shock hazard if inserted into a socket elsewhere
in the house.
The moulded plug on this appliance incorporates a 13 A fuse. Should the fuse need
to be replaced an ASTABEAB approved BS 1362 fuse of the same rating must be
used. Do not forget to refit the fuse cover. In the event of losing the fuse cover the
plug must not be used until a replacement fuse cover has been fitted. Colour of the
replacement fuse cover must be the same colour as that visible on the pin face of
plug must not be used until a replacement fuse cover has been fitted. Colour of the
replacement fuse cover must be the same colour as that visible on the pin face of
the plug. Fuse covers are available from any good electrical store.
IMPORTANT! FITTING A DIFFERENT PLUG
As the colours of the wires in the
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings identifying the terminals
not correspond with the coloured
markings identifying the terminals
in your plug proceed as follows:
(See diagram).
(See diagram).
1. Connect the green-yellow or
green (Earth) wire to the terminal
in the plug marked 'E' or with
the symbol or coloured
green and yellow or green.
green (Earth) wire to the terminal
in the plug marked 'E' or with
the symbol or coloured
green and yellow or green.
2. Connect the blue (Neutral) wire
to the terminal in the plug
marked 'N' or coloured black.
marked 'N' or coloured black.
3. Connect the brown (Live) wire to
the terminal in the plug marked 'L'
or coloured red.
With alternative plugs a 13 A fuse must be fitted either in the plug or adaptor or
or coloured red.
With alternative plugs a 13 A fuse must be fitted either in the plug or adaptor or
in the main fuse box.
If in doubt contact a qualified electrician.
If in doubt contact a qualified electrician.
3
FITTED WITH
BS 1362 13A FUSE AL
W
A
YS
FIT BS 1362 REPLACEMENT
CAR
TRIDGE FUSE
GREEN &
YELLOW
OR
GREEN
N
BLUE
OR
BLACK
L
BROWN
OR
RED
22mm.
6mm.
6mm.
6mm.
32mm.
12mm.
FUSE
CORD GRIP