Sony 8000SF User Manual
309
Names and Functions of Parts of the Control Panel
Chap
switcher), and lights amber at other
times.
times.
AUTO TRANS buttons: The left button
applies to DSK1 and the right button to
DSK2; press these buttons to carry out
an auto transition. The transition
immediately starts, and the button
lights amber. When the transition
completes, the button goes off.
DSK2; press these buttons to carry out
an auto transition. The transition
immediately starts, and the button
lights amber. When the transition
completes, the button goes off.
c K-SS (key snapshot) button
Pressing this button, turning it on, enables
the key snapshot mode. In this mode, you
can save and recall key snapshots.
Pressing this button, turning it on, enables
the key snapshot mode. In this mode, you
can save and recall key snapshots.
d Key source name display/key
snapshot buttons
Each column of two buttons relates to the
corresponding downstream key 1 or 2. The
upper button displays the name of the key
fill signal selected for the key, and the
lower button shows the transition rate.
In key snapshot mode, these buttons
correspond to registers 1 to 4 of the keyer
selected with the key delegation buttons,
and pressing a button recalls the key
snapshot. To save a key snapshot, hold
down the [STORE] button in the numeric
keypad control block, and press the button
for the desired register.
corresponding downstream key 1 or 2. The
upper button displays the name of the key
fill signal selected for the key, and the
lower button shows the transition rate.
In key snapshot mode, these buttons
correspond to registers 1 to 4 of the keyer
selected with the key delegation buttons,
and pressing a button recalls the key
snapshot. To save a key snapshot, hold
down the [STORE] button in the numeric
keypad control block, and press the button
for the desired register.
e FTB (fade to black) button
Press this button to fade to black the
program output of the PGM/PST bank, at
the set transition rate. You can set the fade
to black transition rate in the menu.
Press this button to fade to black the
program output of the PGM/PST bank, at
the set transition rate. You can set the fade
to black transition rate in the menu.
f AUTO button
When this button is pressed, the M/E or
PGM/PST bank preview signal selected on
the edit preview bus is automatically
switched to the program signal depending
on the on-air status.
When this button is pressed, the M/E or
PGM/PST bank preview signal selected on
the edit preview bus is automatically
switched to the program signal depending
on the on-air status.
g Preview selection buttons
Press one of these buttons to select a signal
on the edit preview bus. Each button can be
assigned to any preview output in setup (see
Chapter 16 “Overall Control Panel
Settings (Config Menu)” (Volume 2)).
PST (preset): When this button is pressed,
Press one of these buttons to select a signal
on the edit preview bus. Each button can be
assigned to any preview output in setup (see
Chapter 16 “Overall Control Panel
Settings (Config Menu)” (Volume 2)).
PST (preset): When this button is pressed,
the signal selected on the background B
row of the PGM/PST bank is selected
on the edit preview bus.
row of the PGM/PST bank is selected
on the edit preview bus.
M/E 1 to M/E 3, P/P (M/E1 to M/E 3, P/P
preview): The preview signal (M/E-1
PVW, M/E-2 PVW, M/E-3 PVW, P/P
PVW) of the M/E or PGM/PST bank
corresponding to the pressed button is
selected on the edit preview bus.
PVW, M/E-2 PVW, M/E-3 PVW, P/P
PVW) of the M/E or PGM/PST bank
corresponding to the pressed button is
selected on the edit preview bus.
M/E1 K to M/E3 K, P/P K (M/E1 to M/E
3, P/P key preview): The key preview
signal (M/E-1 K-PVW, M/E-2 K-
PVW, M/E-3 K-PVW, P/P K-PVW) of
the M/E or PGM/PST bank
corresponding to the pressed button is
selected on the edit preview bus.
signal (M/E-1 K-PVW, M/E-2 K-
PVW, M/E-3 K-PVW, P/P K-PVW) of
the M/E or PGM/PST bank
corresponding to the pressed button is
selected on the edit preview bus.
DME V (DME monitor video): When this
button is pressed, the DME monitor
output video signal (DME MON V) is
selected on the edit preview bus.
output video signal (DME MON V) is
selected on the edit preview bus.
DME K (DME monitor key): When this
button is pressed, the DME monitor
output key signal (DME MON K) is
selected on the edit preview bus.
output key signal (DME MON K) is
selected on the edit preview bus.