Runco DR-300c User Manual
13
Remote Control Description
A. IR OUTPUT INDICATOR
Illuminates when a button is pressed, indicating that an IR signal is being
transmitted.
transmitted.
B. POWER BUTTON
Toggles the power on and off. For a discrete on or off command, you can
use the direct access buttons (see 'J'). Note: When the main AC power
switch is first turned ON, the PFP Controller will go through an initiation
cycle for approximately 15 seconds. The PFP Controller cannot be turned
on or operated until the initialization is complete.
C. UP BUTTON
When no menus are present on-screen, the UP button will toggle you
through aspect ratios in the following order:
Letterbox
Standard (4:3) Anamorphic
When the menu is on-screen, the UP button will move the cursor up within
the menu. When an adjustment item has been selected (i.e. brightness),
the UP button will increase the value of that function.
D. LEFT
BUTTON
When no menus are present on-screen, the LEFT button will toggle you
through the four different sources in the following order:
RGB/Component
through the four different sources in the following order:
RGB/Component
Component
S-Video
Composite
E. DOWN
BUTTON
When no menus are present on-screen, the DOWN button will toggle you
through aspect ratios in the following order:
Anamorphic Standard (4:3)
Letterbox
When the menu is on-screen, the DOWN button will move the cursor
down within the menu. When an adjustment item has been selected (i.e.
brightness), the DOWN button will decrease the value of that function.
F. RIGHT
BUTTON
When no menus are present on-screen, the RIGHT button will toggle you
through the four different sources in the following order:
Composite
S-Video
Component
RGB/Component
G. MENU BUTTON
Pressing the MENU button will bring up the main menu. If no action is
taken within approximately 10 seconds, the menu will time-out (disappear).
Also, if you are in an adjustment mode or function, pressing MENU will
bring the menu back one level.
taken within approximately 10 seconds, the menu will time-out (disappear).
Also, if you are in an adjustment mode or function, pressing MENU will
bring the menu back one level.
H. ENTER BUTTON
When an item is highlighted on a menu, pressing ENTER will select that
item.
item.
I.
PROGRAM BUTTON
If the remote control loses its 'memory' as a result of weak or dead batter-
ies, it must be re-programmed for the PFP Controller's code set.
To reprogram the remote, press the PROGRAM button followed by 0,1,3.
Note: Pressing Enter after typing in the code is not necessary.
ies, it must be re-programmed for the PFP Controller's code set.
To reprogram the remote, press the PROGRAM button followed by 0,1,3.
Note: Pressing Enter after typing in the code is not necessary.
J.
DIRECT ACCESS BUTTONS
These buttons will allow you to directly
access an aspect ratio, source, or turn the
unit on or off without having to go through
any menus. These buttons are:
access an aspect ratio, source, or turn the
unit on or off without having to go through
any menus. These buttons are:
1: Selects COMPOSITE video
2: Selects S-VIDEO
3: Selects COMPONENT video
4: Not used
5: Selects RGB/COMPONENT
6: Enables or disables the Installation
Menu (see page 21)
7: Selects the ANAMORPHIC aspect ratio
8: Selects the STANDARD (4:3) aspect ratio
9: Selects the LETTERBOX aspect ratio
0: Turns the PFP Controller ON.
OFF: Also known as the button left of '0',
this turns the PFP Controller OFF.
2: Selects S-VIDEO
3: Selects COMPONENT video
4: Not used
5: Selects RGB/COMPONENT
6: Enables or disables the Installation
Menu (see page 21)
7: Selects the ANAMORPHIC aspect ratio
8: Selects the STANDARD (4:3) aspect ratio
9: Selects the LETTERBOX aspect ratio
0: Turns the PFP Controller ON.
OFF: Also known as the button left of '0',
this turns the PFP Controller OFF.
M
R
UNCO
PWR
A
B
C
D
E
J
F
G
H
I
1
2
3
4
5
6
7
8
9
I
N
P
U
T
0
N
P
P
U
T
I
OFF
ON