ZyXEL Communications P-202H Plus v2 User Manual
P-202H Plus v2 Quick Start Guide
5
If you select Don't Care, then all data calls are routed to the P-202H Plus v2 itself. Analog calls, however, are
routed to either A/B adapter 1 or 2, or simply ignored, depending on the Analog Call Routing field. If
Incoming Phone Number Matching is Don't Care and Analog Call Routing is either A/B Adapter 1, A/B
Adapter 2 or Both, then the P-202H Plus v2 uses Global Analog Call to decide how to handle global calls. If
you set Global Analog Call to Accept, then global calls are routed to the port according to the Analog Call
Routing setting; if you set Global Analog Call to Ignore, then the P-202H Plus v2 ignores all global calls. If
Analog Call Routing is Ignore to begin with, then all analog calls, including global calls, are ignored.
Click Next to continue.
routed to either A/B adapter 1 or 2, or simply ignored, depending on the Analog Call Routing field. If
Incoming Phone Number Matching is Don't Care and Analog Call Routing is either A/B Adapter 1, A/B
Adapter 2 or Both, then the P-202H Plus v2 uses Global Analog Call to decide how to handle global calls. If
you set Global Analog Call to Accept, then global calls are routed to the port according to the Analog Call
Routing setting; if you set Global Analog Call to Ignore, then the P-202H Plus v2 ignores all global calls. If
Analog Call Routing is Ignore to begin with, then all analog calls, including global calls, are ignored.
Click Next to continue.
7 The second wizard screen helps you
set up your P-202H Plus v2 for Internet
access.
In the Service Name field, enter your
ISP's name. Enter the Primary and the
Secondary Phone numbers to connect
to the ISP. Next, enter the user name and
password exactly as your ISP assigned
them.
Select Obtain an IP Address
Automatically if you have a dynamic IP
address; otherwise select Static IP
Address and type your ISP assigned IP
address in the text box below.
Choose the type of Network Address
Translation (NAT) you need. Select Full
Feature if you have multiple public WAN
IP addresses for your P-202H Plus v2.
Select SUA Only if you have just one
public WAN IP address for your P-202H
Plus v2. Select None to disable NAT.
access.
In the Service Name field, enter your
ISP's name. Enter the Primary and the
Secondary Phone numbers to connect
to the ISP. Next, enter the user name and
password exactly as your ISP assigned
them.
Select Obtain an IP Address
Automatically if you have a dynamic IP
address; otherwise select Static IP
Address and type your ISP assigned IP
address in the text box below.
Choose the type of Network Address
Translation (NAT) you need. Select Full
Feature if you have multiple public WAN
IP addresses for your P-202H Plus v2.
Select SUA Only if you have just one
public WAN IP address for your P-202H
Plus v2. Select None to disable NAT.
Note: When you select Full Feature you
must configure at least one
address mapping set. For more
information about NAT and the choices listed refer to your User's Guide.
address mapping set. For more
information about NAT and the choices listed refer to your User's Guide.
In the Transfer Type drop-down list box, choose the type of connection between the router and this remote
node. Select 64K, or Leased. If you selected 64K, select the way you use the PPP Multilink protocol. You
can either select not to (Off) or always (Always) to bundle multiple links in a single connection to boost the
effective throughput between two nodes. Otherwise, select BOD (Bandwidth on Demand) to add or subtract
links dynamically according to traffic demand.
In the Max Idle Timeout field, enter the amount of time (in seconds) after which you want the connection to
timeout if the line remains consistently idle.
Click Next.
node. Select 64K, or Leased. If you selected 64K, select the way you use the PPP Multilink protocol. You
can either select not to (Off) or always (Always) to bundle multiple links in a single connection to boost the
effective throughput between two nodes. Otherwise, select BOD (Bandwidth on Demand) to add or subtract
links dynamically according to traffic demand.
In the Max Idle Timeout field, enter the amount of time (in seconds) after which you want the connection to
timeout if the line remains consistently idle.
Click Next.