Sony BKS-R1601 User Manual

5-24

ROUTING SWITCHER SYSTEM (E)

5-1. Setting Items of the Primary Station

DISPLAY TABLE DATA DVS-V6464B V2.10 STATION NUMBER 1

0000:49 4E 00 00 00 00 00 00 4F 55 54 00 00 00 00 00 : IN......OUT.....

0010:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ................

0020:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ................

0030:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ................

0040:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ................

0050:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ................

0060:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ................

0070:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ................

0080:56 49 44 00 00 00 00 00 41 31 00 00 00 00 00 00 : VID.....A1......

0090:41 32 00 00 00 00 00 00 34 00 00 00 00 00 00 00 : A2......4.......

00A0:35 00 00 00 00 00 00 00 36 00 00 00 00 00 00 00 : 5.......6.......

00B0:37 00 00 00 00 00 00 00 38 00 00 00 00 00 00 00 : 7.......8.......

00C0:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ................

00D0:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ................

00E0:00 00 00 00 00 00 00 00 00 02 FF FF 10 00 00 02 : ................

Ctrl-E:RETURN TO MENUÅ

SET UNIT DETECTABLE DVS-V6464B V2.10 STATION NUMBER 1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

001-020 M ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

021-040 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

041-060 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

061-080 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?

081-100

101-120

121-140

141-160

161-180

181-200

201-220

221-240

241-254

* * * * * *

01:DVS-V1616 02:DVS-V3232 03:DVS-A3232 04:BKS-R1601 05:BKS-R3202

06:BKS-R3203 07:BKS-R3281 08:DVS-V6464 09:BKS-R5000 10:DVS-RS1616

11:DVS-TC3232 12:BKDM-5080 13:BKS-R3204 14:BKS-R3205 15:BKS-R3206

16:BKS-R3280 17:BZR-1000 18:DVS-V3232B 19:DVS-V6464B

Ctrl-E:RETURN TO MENU

Y : DISPLAY TABLE (Except for HDS-V3232)

Purpose

This menu is used to display the table data set with the

control terminal.

Operation Procedure

Select menu item [Y]. The following message will be

displayed at the bottom of the screen.

Display : “DISPLAY TABLE DATA? (y/a/n)”

Press [E], and the signal format (4: 2: 2/4 fsc) set for
each input/output will be displayed in hexadecimal.

(DVS-V

* * * * series only.)

Press [A], and all table data will be displayed in

hexadecimal.
When [N] is pressed, the table data display will be

canceled.

If [SPACE] is pressed during the display, the display

will be interrupted. When [SPACE] is pressed once
again, the display will begin.

Press [Ctrl]

_ [E] to stop the display. The menu

screen will be displayed.

Example of Display

n
For the contents of the table data, refer to the S-BUS
Protocol Manual.

Z : SET UNIT DETECTABLE

Purpose

This menu is used to check the possibility of communica-

tion of secondary stations connected to the S-BUS data
link periodically.

During checking, “?” appears. After the completion of
checking, the code number indicating the type of each

device appears.
If the secondary station does not communicate for a given

period, the message below appears.

“STATION

FAILURE (DISCONNECT OR POWER DOWN)”

Station number

Setting Procedure

Select the menu item [Z].

Select a secondary station you want to check using the

cursor.

Press [Enter], and “?” appears.

To cancel “?”, press [Enter] again.

Press [Ctrl]

_ [E], and the display is changed to the

menu screen to begin checking.

After about ten seconds, select the menu item [Z]. If

the secondary station is available for communication,
“?” changes to a device code number.

n
A secondary station to be checked should be set available
for communication in advance at menu item [F : SET

ACTIVE UNIT NUMBER]

Example of Setting Screen