Rocketfish RF-WHD100 Leaflet

RF-WHD100

This guide contains important safety instructions. Read and follow all 
instructions carefully while installing and using the adapter. Read this 
guide thoroughly before trying to unpack, install, or use your adapter. 
Save these instructions in a readily accessible place.
•  Caution: Always treat your adapter with care and keep it in a clean 
  and dust-free place.
•  Do not expose your adapter to liquid or moisture or humidity.
•  Do not expose your adapter to temperatures above 104°F (40°C) 
  when unit is operated. 
•  Do not drop or throw your adapter.
•  Do not attempt to disassemble or modify your adapter. Only 
  authorized personnel should perform service.
•  Your adapter is not water-resistant. Keep it dry.
•  Do not use a different AC adapter to avoid unit burn or smoke. 

 • 60 

GHz 

WirelessHD 

transmitter 

 • 60 

GHz 

WirelessHD 

receiver

 • HDMI 

cables 

(2)

1  Link LED (blue)
  On—Indicates the receiver is linked to the transmitter.
  Off—Indicates devices are not linked. Reset both devices.
  Blinking—Waiting for a link.
2  Weak LED (green)
  On—Indicates the signal is weak. (The Strong LED will be off.)
  Off—Indicates there is no link or no signal.
3  Strong LED (green)
  On—Indicates the signal is strong. (The Weak LED will be on.)
  Off—Indicates the signal is weak. (The Weak LED will be on.)
Warning: If all four LEDs are blinking at the same time, the internal 
cooling fan is not working. Turn off the adapter and contact 
Rocketfish customer service.
4 Power indicator
  On—Indicates power is connected and turned on.
  Off—Indicates power is turned off.

5  RESET AND CFG
  These buttons are for service at the factory only, please do not 
 press 

them.

6 DC-IN
  Connect the power adapter to this jack and to a power outlet. 
7 Power switch
  Press the Power switch to turn the unit on. 
8 HDMI
  Used to connect the HDMI cables from the source component to 
  the transmitter, and from the receiver to the TV/Projector.

To attach the base stands:
1  Align the holes on the 
  base stand with the 
  mounting tabs on the 
  bottom of the 
 transmitter 

or 

receiver.

2  Press the stand down, 
  then slide it to the left 
  so the tabs hold the 
  stand in place.

To connect the transmitter and receiver:
1  Connect one HDMI cable from the output 
  of the source component (Blu-ray/DVD 
  player, Gaming console, Computer, etc.) to 
  the input on the back of the transmitter unit.
 Note: The transmitter can be used in 
  conjunction with Rocketfish model 
  RF-HDMI4, 4-way HDMI Selector, to 
  send HD signals wirelessly from up 
  to four source components.
 Note: For connection to a computer 
  with a DVI output, use Rocketfish 
  model RF-G1174 HDMI-to-DVI Adapter. 
2  Connect the other HDMI cable from the 
  output on the back of the receiver unit to
  an available HDMI input on the HDTV or
 HD 

Projector.

3  Connect the power cords to the 
 DC 

IN jacks on the transmitter and 

  receiver and to a power outlet.
4  Turn on the connected devices, then 
  press the power switches on the 
  transmitter and receiver to the ON 
 position.

For best results, the transmitter and receiver should: 
  •  Face each other within the same room
  •  Be no more than 33 feet (10 meters) apart
  •  Be on the same level (one should not be higher than the other)
  •  In open spaces (not in a cabinet or an enclosed shelf)
Note: If you begin to see your video breaking up, try repositioning 
the device providing the transmitter as many open paths to the 
receiver as possible.

•  Power adapters (2)
•  Base mounting brackets (2)
• Quick Setup Guide