DELL 9.7(0.0) User Manual
CONFIGURATION mode
ip control-plane [egress filter]
2. Apply Egress ACLs to IPv6 system traffic.
CONFIGURATION mode
ipv6 control-plane [egress filter]
3. Create a Layer 3 ACL using permit rules with the count option to describe the desired CPU traffic.
CONFIG-NACL mode
permit ip {source mask | any | host ip-address} {destination mask | any |
host ip-address} count
host ip-address} count
Dell Networking OS Behavior: Virtual router redundancy protocol (VRRP) hellos and internet group
management protocol (IGMP) packets are not affected when you enable egress ACL filtering for CPU
traffic. Packets sent by the CPU with the source address as the VRRP virtual IP address have the interface
MAC address instead of VRRP virtual MAC address.
management protocol (IGMP) packets are not affected when you enable egress ACL filtering for CPU
traffic. Packets sent by the CPU with the source address as the VRRP virtual IP address have the interface
MAC address instead of VRRP virtual MAC address.
Counting ACL Hits
You can view the number of packets matching the ACL by using the count option when creating ACL
entries.
1.
.
2. Apply the ACL as an inbound or outbound ACL on an interface. Refer to
3. show ip accounting access-list
EXEC Privilege mode
View the number of packets matching the ACL.
IP Prefix Lists
IP prefix lists are supported to control routing policy.
An IP prefix list is a series of sequential filters that contain a matching criterion (examine IP route prefix)
and an action (permit or deny) to process routes. The filters are processed in sequence so that if a route
prefix does not match the criterion in the first filter, the second filter (if configured) is applied. When the
route prefix matches a filter, the system drops or forwards the packet based on the filter’s designated
action. If the route prefix does not match any of the filters in the prefix list, the route is dropped (that is,
implicit deny).
A route prefix is an IP address pattern that matches on bits within the IP address. The format of a route
prefix is A.B.C.D/X where A.B.C.D is a dotted-decimal address and /X is the number of bits that should be
matched of the dotted decimal address. For example, in 112.24.0.0/16, the first 16 bits of the address
112.24.0.0 match all addresses between 112.24.0.0 to 112.24.255.255.
and an action (permit or deny) to process routes. The filters are processed in sequence so that if a route
prefix does not match the criterion in the first filter, the second filter (if configured) is applied. When the
route prefix matches a filter, the system drops or forwards the packet based on the filter’s designated
action. If the route prefix does not match any of the filters in the prefix list, the route is dropped (that is,
implicit deny).
A route prefix is an IP address pattern that matches on bits within the IP address. The format of a route
prefix is A.B.C.D/X where A.B.C.D is a dotted-decimal address and /X is the number of bits that should be
matched of the dotted decimal address. For example, in 112.24.0.0/16, the first 16 bits of the address
112.24.0.0 match all addresses between 112.24.0.0 to 112.24.255.255.
The following examples show permit or deny filters for specific routes using the le and ge parameters,
where x.x.x.x/x represents a route prefix:
where x.x.x.x/x represents a route prefix:
• To deny only /8 prefixes, enter deny x.x.x.x/x ge 8 le 8.
• To permit routes with the mask greater than /8 but less than /12, enter permit x.x.x.x/x ge 8.
• To permit routes with the mask greater than /8 but less than /12, enter permit x.x.x.x/x ge 8.
108
Access Control Lists (ACLs)