DELL 9.7(0.0) User Manual
Example of Debugging a VLAN and its Ports
The port notations are as follows:
The port notations are as follows:
• MT — stacked trunk
• MU — stacked access port
• T — 802.1Q trunk port
• U — 802.1Q access port
• NU — Native VLAN (untagged)
• MU — stacked access port
• T — 802.1Q trunk port
• U — 802.1Q access port
• NU — Native VLAN (untagged)
Dell# debug member vlan 603
vlan id : 603
ports : Te 1/47 (MT), Te 2/1(MU), Te 2/25(MT), Te 2/26(MT), Te 2/27(MU)
Dell#debug member port tengigabitethernet 1/47
vlan id : 603 (MT), 100(T), 101(NU)
VLAN Stacking in Multi-Vendor Networks
The first field in the VLAN tag is the tag protocol identifier (TPID), which is 2 bytes. In a VLAN-stacking
network, after the frame is double tagged, the outer tag TPID must match the TPID of the next-hop
system.
While 802.1Q requires that the inner tag TPID is 0x8100, it does not require a specific value for the outer
tag TPID. Systems may use any 2-byte value. The switch uses 0x9100 (shown in the following) while non-
Dell Networking devices might use a different value.
If the next-hop system’s TPID does not match the outer-tag TPID of the incoming frame, the system
drops the frame. For example, as shown in the following, the frame originating from Building A is tagged
VLAN RED, and then double-tagged VLAN PURPLE on egress at R4. The TPID on the outer tag is 0x9100.
R2’s TPID must also be 0x9100, and it is, so R2 forwards the frame.
tag TPID. Systems may use any 2-byte value. The switch uses 0x9100 (shown in the following) while non-
Dell Networking devices might use a different value.
If the next-hop system’s TPID does not match the outer-tag TPID of the incoming frame, the system
drops the frame. For example, as shown in the following, the frame originating from Building A is tagged
VLAN RED, and then double-tagged VLAN PURPLE on egress at R4. The TPID on the outer tag is 0x9100.
R2’s TPID must also be 0x9100, and it is, so R2 forwards the frame.
Given the matching-TPID requirement, there are limitations when you employ Dell Networking systems
at network edges, at which, frames are either double tagged on ingress (R4) or the outer tag is removed
on egress (R3).
at network edges, at which, frames are either double tagged on ingress (R4) or the outer tag is removed
on egress (R3).
VLAN Stacking
The default TPID for the outer VLAN tag is 0x9100. The system allows you to configure both bytes of the
2 byte TPID.
Previous versions allowed you to configure the first byte only, and thus, the systems did not differentiate
between TPIDs with a common first byte. For example, 0x8100 and any other TPID beginning with 0x81
were treated as the same TPID, as shown in the following illustration. The system differentiates between
0x9100 and 0x91XY, as shown in the following illustration.
You can configure the first 8 bits of the TPID using the vlan-stack protocol-type command.
between TPIDs with a common first byte. For example, 0x8100 and any other TPID beginning with 0x81
were treated as the same TPID, as shown in the following illustration. The system differentiates between
0x9100 and 0x91XY, as shown in the following illustration.
You can configure the first 8 bits of the TPID using the vlan-stack protocol-type command.
The TPID is global. Ingress frames that do not match the system TPID are treated as untagged. This rule
applies for both the outer tag TPID of a double-tagged frame and the TPID of a single-tagged frame.
applies for both the outer tag TPID of a double-tagged frame and the TPID of a single-tagged frame.
For example, if you configure TPID 0x9100, the system treats 0x8100 and untagged traffic the same and
maps both types to the default VLAN, as shown by the frame originating from Building C. For the same
traffic types, if you configure TPID 0x8100, the system is able to differentiate between 0x8100 and
untagged traffic and maps each to the appropriate VLAN, as shown by the packet originating from
Building A.
maps both types to the default VLAN, as shown by the frame originating from Building C. For the same
traffic types, if you configure TPID 0x8100, the system is able to differentiate between 0x8100 and
untagged traffic and maps each to the appropriate VLAN, as shown by the packet originating from
Building A.
824
Service Provider Bridging