Panasonic KX-FP145 User Manual
9. Help
58
For Fax Advantage assistance, call 1-800-435-7329.
9 Help
9For Fax Advantage assistance, call 1-800-435-7329.
Error Messages
9.1 Error messages –
Reports
Reports
If a problem occurs during fax transmission or
reception, one of the following communication
messages will be printed on the sending and
journal reports (page 31).
reception, one of the following communication
messages will be printed on the sending and
journal reports (page 31).
COMMUNICATION ERROR
(Code: 40-42, 46-72, FF)
(Code: 40-42, 46-72, FF)
L
A transmission or reception error occurred.
Try again or check with the other party.
Try again or check with the other party.
COMMUNICATION ERROR
(Code: 43, 44)
(Code: 43, 44)
L
A line problem occurred. Connect the
telephone line cord to a different jack and try
again.
telephone line cord to a different jack and try
again.
L
An overseas transmission error occurred. Try
using the overseas mode (feature #23, page
52).
using the overseas mode (feature #23, page
52).
DOCUMENT JAMMED
L
The document is jammed. Remove the
jammed document (page 66).
jammed document (page 66).
ERROR-NOT YOUR UNIT
(Code: 54, 59, 70)
(Code: 54, 59, 70)
L
A transmission or reception error occurred
because of a problem with the other party’s
fax machine. Check with the other party.
because of a problem with the other party’s
fax machine. Check with the other party.
JUNK FAX PROH. REJECT
L
The junk fax prohibitor of your fax machine
rejected fax reception.
rejected fax reception.
MEMORY FULL
L
The memory is full of received documents
due to a lack of recording paper or a
recording paper jam. Install paper (page 12)
or clear the jammed paper (page 63).
due to a lack of recording paper or a
recording paper jam. Install paper (page 12)
or clear the jammed paper (page 63).
NO DOCUMENT
L
The document was not fed into the unit
properly. Re-insert it and try again.
properly. Re-insert it and try again.
OTHER FAX NOT RESPONDING
L
The other party’s fax machine is busy or has
run out of recording paper. Try again.
run out of recording paper. Try again.
L
The document was not fed properly. Re-
insert the document and try again.
insert the document and try again.
L
The other party’s fax machine rings too many
times. Send the fax manually (page 30).
times. Send the fax manually (page 30).
L
The other party’s machine is not a fax
machine. Check with the other party.
machine. Check with the other party.
L
The number you dialed is not in service.
PRESSED THE STOP KEY
L {
STOP} was pressed and fax communication
was canceled.
OK
L
Fax communication was successful.
9.2 Error messages –
Display
Display
If the unit detects a problem, one or more of the
following messages will appear on the display.
—————————————————————
following messages will appear on the display.
—————————————————————
CALL SERVICE
CALL SERVICE 2
L
There is something wrong with the unit.
Contact our service personnel.
Contact our service personnel.
—————————————————————
CHECK DOCUMENT
L
The document was not fed into the unit
properly. Re-insert the document. If
misfeeding occurs frequently, clean the
document feeder rollers (page 67) and try
again.
properly. Re-insert the document. If
misfeeding occurs frequently, clean the
document feeder rollers (page 67) and try
again.
L
Attempted to transmit a document longer
than 600 mm (23
than 600 mm (23
5
/
8
"). Press {STOP} to
remove the document. Divide the document
into two or more sheets and try again.
into two or more sheets and try again.
—————————————————————
CHECK FILM
L
The ink film is empty. Replace the ink film
with a new one (page 11).
with a new one (page 11).
L
The ink film is not installed. Install it (page
10).
10).
L
The ink film is slack or creased. Tighten it
(see step 5 on page 10).
(see step 5 on page 10).
—————————————————————
CHECK MEMORY
L
The memory (telephone numbers,
parameters, etc.) has been erased. Re-
program.
parameters, etc.) has been erased. Re-
program.
—————————————————————
CHECK PAPER
L
The recording paper is not installed or the
unit has run out of paper. Install paper and
press {START} to clear the message.
unit has run out of paper. Install paper and
press {START} to clear the message.
FP145.book Page 58 Thursday, January 15, 2004 10:46 AM