Panasonic AJ-SD930BE User Guide
19 (E)
Jog mode
Jog/Shuttle
1
Press the search dial so that it remains pressed in.
Check that the JOG lamp has lit.
Check that the JOG lamp has lit.
Shuttle mode
1
Press the search dial so that it is released from the
pressed-in position.
The SHTL lamp lights, and the shuttle mode is
established.
pressed-in position.
The SHTL lamp lights, and the shuttle mode is
established.
O
Immediately after the power is turned on, turn
the search dial and leave it at the centre
position.
the search dial and leave it at the centre
position.
3
To transfer the VTR from the jog mode to another
mode, press the button that corresponds to the
mode concerned.
mode, press the button that corresponds to the
mode concerned.
2
Turn the search dial.
The dial’s click-stops are released, and the tape is
played back at the speed (–1a
The dial’s click-stops are released, and the tape is
played back at the speed (–1a
to +1a)
corresponding to the speed at which the dial is
turned.
The maximum speed can be switched using setup
menu No. 323 (JOG FWD MAX) and No. 324 (JOG
REV MAX) settings.
However, noise will occur at all speeds other than
–0.43a to +0.43a.
When the dial is no longer turned, the still picture
mode is established.
turned.
The maximum speed can be switched using setup
menu No. 323 (JOG FWD MAX) and No. 324 (JOG
REV MAX) settings.
However, noise will occur at all speeds other than
–0.43a to +0.43a.
When the dial is no longer turned, the still picture
mode is established.
3
Turn the search dial.
O
When the SHTL lamp among the JOG, SHTL
and SLOW lamps is lit, the playback picture
speed changes from 0 up to ±32a depending on
the dial position.
This speed can be switched to ±8.4a, ±16a or
±32a using setup menu No. 101 (SHTL MAX).
The dial has a click-stop at the centre position
where the still picture mode is established.
and SLOW lamps is lit, the playback picture
speed changes from 0 up to ±32a depending on
the dial position.
This speed can be switched to ±8.4a, ±16a or
±32a using setup menu No. 101 (SHTL MAX).
The dial has a click-stop at the centre position
where the still picture mode is established.
O
When the SLOW lamp among the JOG, SHTL
and SLOW lamps is lit, the playback picture
speed changes from –4.1 up to +4.1a
depending on the dial position.
The maximum speed can be switched using
setup menu No. 320 (VAR FWD MAX) and No.
321 (VAR REV MAX) settings. However, noise
will occur at all speeds other than –0.43a to
+0.43a, +0.5a and +0.75a.
The dial has a click-stop at the centre position
where the still picture mode is established.
and SLOW lamps is lit, the playback picture
speed changes from –4.1 up to +4.1a
depending on the dial position.
The maximum speed can be switched using
setup menu No. 320 (VAR FWD MAX) and No.
321 (VAR REV MAX) settings. However, noise
will occur at all speeds other than –0.43a to
+0.43a, +0.5a and +0.75a.
The dial has a click-stop at the centre position
where the still picture mode is established.
4
To transfer the VTR from the shuttle mode to
another mode, press the STOP button or other
button.
another mode, press the STOP button or other
button.
2
Press the SHTL/SLOW button and switch to SHTL
or SLOW.
or SLOW.
<Note>
The direct search mode in which the VTR is
transferred to the shuttle mode or jog mode by turning
the search dial is set at the factory.
By selecting KEY as the setup menu No. 100
(SEARCH ENA) setting, the VTR can be set to the
mode in which it will not be transferred to the search
mode unless the search button is pressed.
The direct search mode in which the VTR is
transferred to the shuttle mode or jog mode by turning
the search dial is set at the factory.
By selecting KEY as the setup menu No. 100
(SEARCH ENA) setting, the VTR can be set to the
mode in which it will not be transferred to the search
mode unless the search button is pressed.
<Notes>
O
It is possible to listen to playback audio in the –10
to +10 speed range from the audio monitor output.
(PCM must be selected for the setup menu No. 721
(MONI CH SELECT) setting.)
to +10 speed range from the audio monitor output.
(PCM must be selected for the setup menu No. 721
(MONI CH SELECT) setting.)
O
The audio playback sound heard in the search
mode contains noise.
mode contains noise.