ALTINEX MT115-111 User Manual
MULTITASKER
400-0443-004
10
7.2 DESCRIPTION OF COMMANDS
Each command consists of three parts:
Function, Card ID, and Unit ID.
Function, Card ID, and Unit ID.
[ Function , Card ID , Unit ID ]
Example: [VERC3U2]
VER
= Function
C3
= Card ID or Group ID
U2
= Unit ID (optional for Unit ID 0)
For Function, see a detailed explanation under
each command description.
each command description.
The card ID is a unique identifier. It is equal to
the enclosure slot number, or it may be an
assigned value. As the slot number, the value
can range from 1-4 up to 1-20 depending on the
enclosure. If the value is assigned, the ID may
be a maximum of 99. Card ID 0 (C0) is used for
the controller and cannot be reassigned.
the enclosure slot number, or it may be an
assigned value. As the slot number, the value
can range from 1-4 up to 1-20 depending on the
enclosure. If the value is assigned, the ID may
be a maximum of 99. Card ID 0 (C0) is used for
the controller and cannot be reassigned.
The group ID is a number representing a group
of cards defined with the [WR] command. When
using the group ID, all cards in the group will
perform the given instruction.
of cards defined with the [WR] command. When
using the group ID, all cards in the group will
perform the given instruction.
NOTE: In this guide, cards are referenced by
their IDs (C1, C2...C99). Typically, the ID
number will be equivalent to the slot number.
Groups will be referenced by their IDs (G1-G8).
their IDs (C1, C2...C99). Typically, the ID
number will be equivalent to the slot number.
Groups will be referenced by their IDs (G1-G8).
Changing the position of a card will significantly
affect the commands recorded on software
definitions or third-party control systems.
affect the commands recorded on software
definitions or third-party control systems.
The unit ID has a range from U0 to U20. U0
should be used for single unit operation. If the ID
is set to U0, each command may be used
without Ui. Use the command [SETU0], as
explained in the MT101-101 User’s Guide.
should be used for single unit operation. If the ID
is set to U0, each command may be used
without Ui. Use the command [SETU0], as
explained in the MT101-101 User’s Guide.
Example:
[VERC3]:
For U0
[VERC3Ui]: For ID other than U0
[VERC3]:
Equivalent to [VERC3U0]
COMMAND ORGANIZATION
The RS-232 commands in this section are
organized into the following 5 categories:
organized into the following 5 categories:
Basic Commands
Feedback Control
Card Control
Card IDs
Groups
See the SUMMARY OF COMMANDS (Section 7.3)
for one-line descriptions of each command.
for one-line descriptions of each command.
BASIC COMMANDS
The basic commands are used to provide general
information about the card. These commands are
most useful during the initial stages of setting up
and operating the card.
information about the card. These commands are
most useful during the initial stages of setting up
and operating the card.
1. [VER]
This command displays the software version
and card type for the MT115-111 card.
and card type for the MT115-111 card.
Command Format: [VERCn]
Cn = Card ID (n = slot # from 1 to max slots)
Example:
An MT115-111 card is in slot 4. Send the
command [VERC4], and the system will return
feedback similar to the following:
command [VERC4], and the system will return
feedback similar to the following:
[MT115-111 690-0231-001 C04]
MT115-111
= Card model number
690-0231-001 = Firmware version
C04
= Card ID