Skylink SW-433 Leaflet
1. In order for the Silent Alarm to recognize different transmitters, they must first be“learned” to the Silent Alarm.
2. Plug in the Silent Alarm to an electrical outlet (its red LED light wi ll go on). Plug in an appliance (i.e. light, radio,
2. Plug in the Silent Alarm to an electrical outlet (its red LED light wi ll go on). Plug in an appliance (i.e. light, radio,
maximum 1200 watts) to the outlet of the Silent Alarm.
3. Turn on the appliance that is plugged into the Silent Alarm. Turn on the Silent Alarm
by pressing the “ON/OFF” button. The appliance should be on after the “ON/OFF”
button is pressed. If you press the “ON/OFF” button again, the appliance will be
turned off.
button is pressed. If you press the “ON/OFF” button again, the appliance will be
turned off.
4. With the Silent Alarm plugged in, press and hold the “SET” button on the unit
(its red LED light will flash). Simultaneously activate the sensor that you want
to program to the silent alarm until the red LED light on the silent alarm stops
flashing indicating it has learned the code.
to program to the silent alarm until the red LED light on the silent alarm stops
flashing indicating it has learned the code.
5. Test the sensor by activating it while the Silent Alarm and the appliance are plugged
in. The appliance will turn on and off for approxim ately 15 seconds. If the appliance
that you plugged in does not turn on and off, repeat the above procedures .
that you plugged in does not turn on and off, repeat the above procedures .
Programming the transmitter and the Silent Alarm
Warranty
If, within one year from date
of purchase, this product
should become defective,
due to faulty workmanship
or materials, it will be re-
paired or replaced, without
charge. Proof of purchase
is required.
of purchase, this product
should become defective,
due to faulty workmanship
or materials, it will be re-
paired or replaced, without
charge. Proof of purchase
is required.
transmit a signal to the Silent
Alarm, and the appliance that
has been plugged into the
silent alarm will be turned on
and off for approximately 15
seconds. If a lamp is plugged
into the Silent Alarm, the light
will flash so that it can notify
the hearing impaired. (or you
may plug in a radio to warn
the visually impaired)
Alarm, and the appliance that
has been plugged into the
silent alarm will be turned on
and off for approximately 15
seconds. If a lamp is plugged
into the Silent Alarm, the light
will flash so that it can notify
the hearing impaired. (or you
may plug in a radio to warn
the visually impaired)
SILENT ALARM
USER'S INSTRUCTIONS
(Model SW-433)
®
Introduction
The Silent Alarm (SW-433)
is designed to work with all
Skylink sensors that in-
corporate the rolling code
technology. This alarm can
work with as many as 15
different sensors. For
instance, it can work with
the Security System Control
Panel, Temperature Sen-
sor, Smoke Alarm Sensor,
Vibration Sensor, Flood
Sensor, Door/Window Sen-
sor are activated. They will
is designed to work with all
Skylink sensors that in-
corporate the rolling code
technology. This alarm can
work with as many as 15
different sensors. For
instance, it can work with
the Security System Control
Panel, Temperature Sen-
sor, Smoke Alarm Sensor,
Vibration Sensor, Flood
Sensor, Door/Window Sen-
sor are activated. They will
FCC
WARNING:
Changes or modifications
to this unit not expressly
approved by the party res-
ponsible of compliance
could void the user’s
authority to operate the
equipment.
Changes or modifications
to this unit not expressly
approved by the party res-
ponsible of compliance
could void the user’s
authority to operate the
equipment.
The Remote Control is
approved by the FCC and
it complies with Part 15
of the FCC Rules. Its
operation is subject to the
following two conditions :
1. This device may not
approved by the FCC and
it complies with Part 15
of the FCC Rules. Its
operation is subject to the
following two conditions :
1. This device may not
cause harmful inter-
ference.
ference.
2. This device must accept
any interference that
may cause undesired
operation.
may cause undesired
operation.
® are registered trademarks of their
respective corporations
NOTE
Skylink will not be held
liable or responsible for
any misuse or application
of this product other than
for its intended use.
liable or responsible for
any misuse or application
of this product other than
for its intended use.
I f you would like to order Skylink’s
product or have difficulty getting
them to work, please :
1. visit our website FAQ section at
product or have difficulty getting
them to work, please :
1. visit our website FAQ section at
www.skylinkhome.com , or
2. email us at
support@skylinkhome.com , or
3. call our toll free at 1-800-304-1187
from Monday to Friday, 9 am to
5 pm EST.
fax: 1-800-286-1320
5 pm EST.
fax: 1-800-286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton,
Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101A091-001
US Patent 6243000B1
©2005 SKYLINK GROUP
17 Sheard Avenue, Brampton,
Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101A091-001
US Patent 6243000B1
©2005 SKYLINK GROUP